Search results

just curious to kno what sum of u guys cranking compression is on stock motors vs bigger bores like 67mm 68mm??? i have a stocker at 127

LOOKIN FOR LEFT SIDE CASE NO CRACKS SHIPPED TO CENTRAL FLORIDA ASAP HAV SUM CASE DAMAGE AFTER PREVIOUS OWNER PISTON FAILURE

have a piston here with the number 3817A and fresh honed ported cyl with it looking for size/info any help would be great!

so i hav a new project here at the shop and the trans bearing went boom boom all needle bearings fell into clutch cover/case.... question is can i swap this bearing without splitting cases...it is the sprocket shaft

was riding today bike was running fine then it got kinda boggy i eased up to my drive way pulled clutch hit kill switch and the bike all the sudden revved outta control has 280 main needle clip 4th from top dg head pipe powercore silencer open airbox....theres plenty of slack in cable tors has...

forgot my password sold bikes years went by but guess what im back ..... my buddy picked up a blaster last night and called me with sum tuning issues i remembered u guys!!!

Here she is Hot rods crank kit new bearings New snap rings washers etc greased and loctite on all seals 150 psi compression Boyesen pro series reeds Fired right up and sounds awesome Waitin on front hub bearings and steering stem b4 the test run! Thanks mr oconner for all the vids he...

How do I remove the counter bearing and the other small bearing on the side side??

Anyone ridin rancho this year Heard a lot of problems been goin on out there used to ride Every weekend up ther never had a problem Wondering if anyone has rode there this new year

So check her out 700 for complete blaster with bent frame....new frame 25 bucks On craigslist!!! Took me 6 hrs to swap!.....I have another in the mid stages of build (Wifes)she wanted the

Got my hot rods kit last night and ready to build Was wondering if I can press in these bearings instead of sweating I have a press at my shop also was wondering how can I check.clearances To insure bearings are fully seated?? Any help would be awesome

Anyone ever reused the case bolts how do u torque them from factory? Do I need new ones??

Any holley pros here? Gotta 670 street avenger carb about a month ago And I'm ready to throw it in the can 74 primary 80 secondary jets .031 shooter sputters mid throttle and off idle stumble driving me nuts Anyone familiar with these carbs Installed on 91 l98 350 aluminum ported heads...

Sooo I got this quad 1 week ago....new piston but...the old one broke and chunk got stuck in crank case crack yada yada I'm wondering if u would run this or if anyone has had success with jb weld?? Area was cleaned and prepped very well just looking for opinion If this is a omg no way wtf...

So I've owned this blaster 6 days and here sum b4 and afters

split cases and found small chunk of aluminum wedged in rod Also have a crack I believe from the chain I'm familiar with brazing and have done it b4 Never on a blaster Can she be saved?

How is the best way to remove the phillips case bolts without damage I'm. Havn trouble and don't want to damge the fragile phillips head Is there a tq spec for installation?

Can anyone I.d this piston or gimme info on searching? Jug looks good can still see cross hatch pattern But I see sum metal chunks there's a few mm play side to side slight up and down

finally got it running!! Slight pingin from bottom end noticed leak Crack where the cases meet!! Looks like sumthn broke and pushed outward On the case few inches behind drain plug! Any ideas on a fix??

I have an 02 I believe blaster been sittin a while cleaned carb looked nice upon Bowl removal 150 psi compression new plug checked reeds looked kinda bad Replaced with boyeson pro series removed t.o.r.s has spark Fired up ran for a few lil boggy then died hasn't restarted Any help would be...