Search results

just got a 95 banshee, and t has a few problems. the thing that worries me is a small oil leak from the bottom of the engine case, theres a hole(from the factory) that goes in the case about a inch, and theres a small leak from it. its not threaded or anything but it is leaking slightly... and...

well blasty is going goodbye on sunday, im trading for a b16a with gsr cams/tranny with lsd,acura axles and stage 1 clutch for my civic hatch... so ill be quadless but ill have a super shiny motor to work on!!

i might be picking up an older hatch with a blown motor, its an 89 with a good 5spd tranny, it had a 1.6 non v-tec in it, whats a biger motor thats not to hard to find, i was thinking an integra ls motor (1.8 dohc) or something better?? can i use the stock tranny with the 1.8? how bout with...

everyone list a price it would take someone to offer you for your blastys, not what there worth or what the book is.. but what it would take for someone to drive home with it today... my price is 1,800

Leaf Blower Bolt on Dyno pull- Video so does this mean that the electric fans they sell as superchargers to connect to your intake actually work??

ok guys i emailed the guy with the duel exhaust blaster on ebay, and this is what he said ... damn people are dumb I'm very surprised you didn't get my last response. It was quite long. The Blaster is .080 over, which is equal to 228CC engine. Stock engine range in the 55-65MPH This WILL do...

i think the axle is a little wider than stock, it has a durablue sticker on it but idk, also is there a way to tighten up the rear axle? it has play in it but im told the bearings are new?

how can i tel what year a 250x is? the frame has been painted so there for the sticker with the year is gone... i talked to the owner and he said it was either a 98 or 99... i know they stopped making them in 92 so what do i have here? it it possable to put a kicker on a 300ex?

dude wants my blaster and wants to trade for this civic 89 civic on craigslist im thinkin ill tell him the car and 500 cash but idk?

this was my former co-worker and friend, he wasnt wearing his seatbelt thursday night and it cost him his life Cumberland Times-News - dans run FORT ASHBY, W.Va. — Forty-seven-year-old David A. Wolford was fatally injured in a single-vehicle accident late Thursday on Dan’s Run Road...

looking for blaster swinger bearings and seals can be used and a 300ex rear caliper 250x/300ex/400ex are all the same

im trying to come up with a rough hp calculator, by giving ratings to all the common mods, starting with mild to wild, can you give me estimates of the hp normal mods give? such as (this is just guessing) -remove airbox lid and rejet= 1hp -timing advance+4= 2hp -vf3 reeds= 2hp -left hand...

found this on ebay, also found better kits with 2.5lb bottles for around 500bucks, whats everyone think? eBay Motors: ATV & Quad Sneaky Pete Mini Nitrous Kit w/5 NOS Refills (item 380113388820 end time Apr-25-09 06:43:31 PDT)

whats a good sealant to seal bottom cases? it has to be baught at a honda shop im tearing it down this week and cant make it to the yamaha dealer

how long does it take for fuel sitting to separate from the oil? or does this not happen? seems this could be important to know if i have a can of mixed sitting for a couple months and dont shake it before fueling up

check out all the sport quads national makes.. National Motor

ok a few of us have these and i figured id make a thread for them to keep from stopping up others... ill add a few known mods, 400ex carb/a-arms/plastic fits,with some mods a 350x motor mounts up, ive also heard a xr600 motor is an easy swap?? some stock problems are, the exhaust is very...

ok, rode the blasty today and noticed it cutts out at full throttle, like it im putting along and hit the throttle it will cut out or act like its trying to hit the power band, it didnt do this before i put on the clamp on uni, i re jetted to a 300, checked plug it looked good, rode it and it...

what can cause a lower rod bearing to go? like ran fine for a few hours and all of a sudden it loses power and wont idle, tear it down and no bearings at all, the needles arent even in there... everything else it tight, good top end, good crank bearings just the lower rod bearing.... nothing...

anyone know anything bout getting a home loan, theres a house for 16,000 thats in decent shape and id like to try for it but my credit aint that great.. anyone know of any place to finance with bad credit