Search results

2003 Yamaha Blaster

put the 30mm OKO back on runs great of course. I am still breaking in the motor so taking it easy for now. But what does everyone think? The right carb for this setup or should I go bigger?

My father just called and said that he believes he figured the 34mm Round slide mikuni carb out, says the brass fitting on the carb was stopping the cable from allowing the slide to sit all the way in. Says it should work fine now, so Im going to drive an hour to see if he is right. You really...

Nothing wrong with the 30mm OKO just figured since I got it Trail Ported and Bored .60 over that I needed a bigger carb

I know this has been asked many times. What carb should I go with and where can i find it cheap? here are my mods, Bored .60 over, weisco pistons, Trail ported, Boyseen reeds, FMF fatty, FMF powercore silencer, Reed spacer, Alum. Air box, uni filter. before the new trail port and bored .60 I...

**87 KAWASAKI TECATE 4WHEELER**

I ordered some mains and some 22/100 pilots. I am hoping that with a good trail port and bigger carb I can keep up with some of the bigger bikes.

Did the carb make a noticeable diff for you? What style jets does the Flat slide use?

Folks I am receiving my top end back in a day or so. here is my setup topend bored .60 over new weisco piston and rings, Trail ported, Alum. Airbox with Uni filter, Boyseen Carbon reeds, Head mod by Ken, FMF fatty, FMF powercore 2, reed spacer, However right now I am running a 30mm OKO, I have...

I was worried about that, but honestly it still has good travel and the rebound is way better with the new shock

http://cgi.ebay.com/ebaymotors/13-3-8-RFY-Air-Shock-Absorbers-Banshee-YFZ-Warrior-ATV-/180599851832?pt=Motors_ATV_Parts_Accessories&hash=item2a0c970b38 What are your opinions on these? I have stock blaster shocks now

today I made a 4" extended swingarm using steel square stock I cut the swing between the shock and the Carriage. I used a YFZ 450 shock in the stock mounting tabs, all I did was use 2 washers for the top and at the bottom I drilled out the yfz shock and ran the stock pin and cotter key thru...

I have this exact same Carb that i bought off ebay it worked great for me. I have since been bored and ported and going to a 34mm I will sell you the carb for 70 bucks shipped

As of right now here is what I have planned, Porting for sure! New top end. I am not so sure about the stroker..I am not sure I can actually do this myself..Never had a lowerend apart

Well I am going to keep it, Porting will happen in the next few weeks. I will also go ahead and have it bored and a new top end, probably due for one anyhow..How labor intensive is a stroker kit?

I have a 03 Blaster and I am looking for an extended swingarm. Let me know what you have thanks

My mechanical knowledge limits me at this point to just doing a top end rebuild. How big of piston can I fit into a bored out stock cylinder? And with these mods what kind of HP can I expect?

Alright here is where I am at with things. I have a 2003 Blaster with A Head mod from Ken O connor, Boyseen Reeds, Reed Spacer, 30MM Carb, 14T Sproket, FMF Fatty, FMF Powercore 2, Aluminum airbox with Uni and outerwears, I have a the DYI timing advance mod, but currently have it at Stock timing...

Might be a dumb question...Mine is a 2003 and I just have a bent left spindle will this work? also do you want me to purchase thru ebay or thru you on here? i am just trying to figure out what is best for you. Thanks...Be even better if you would just sell me the left side :) Thanks