Search results

So a while ago i picked up a completely stock blaster for my kids to run around the yard and one day i'm watching my step daughter ride around and all of a sudden it started to rev up (air leak starting) higher and higher and i knew something was failing sure enough the exhaust was leaking a...

i have a DT200 with the original wiring harness off the bike i bought it off someone on here a while ago and never got around to doing anything with it i was told it ran when i got it looking to get 750 for it i would like to sell it local but i can ship it within the U.S.

So a friend of mine decided to go buy a 2001 yz250 bike and took the guys word on how well it ran the guy had the been riding it when he got there and he said it ran great when he got it home it wouldn't start so he brought it to me to take a look at the intake boot was cracked and the gaskets...

So i got this issue with my steering i thought the stem was bent from a roll over i had a week ago but it turns out the stem is fine and moves nice and free its the new ASR arms that seem to be causing the problem both the tires are stiff as hell to move i was wondering if anyone else had this issue

So I just bought a new set of kenda klaws for the rear of my quad can anybody explain the arrows that point both ways saying hard in one direction and soft in the other I'm assuming there referring to the terrain but that just a swag

Hey guy I'm not sure if I have a problem or not I'm using atf type f trans fluid when I installed the engine I put in 650 ml in when cold the site window is completely covered and after I warm it up which is when your supposed to check it there's nothing showing I got no funky smell out the pipe...

So I just moved into the area near east aurora ny south of Buffalo and I'm looking for some places to ride I just put in a new rebuilt engine and gotta burn this first tank off and my neighbors ain't gonna tolerate me doing laps around my house much more

So I found a handy way to tighten the jug nuts and be able to torque them as well and I bet everyone has all they need to it grab a 3/8 torque wrench and a 12 mm wrench and use the box end on the nut and the open end to grab the 3/8 drive on your torque wrench line it up so it's straight and use...

So i tried to install my pipe today and it's on but the fitment is not the best i can't get the top mount to bolt up and when i position it near the mount the pipe sides off the header about a 1/4 of an inch and like i mentioned its only near the mount i can't get the mount to line up at all...

So i'm in the middle of taking an 04 blaster and adding a bunch of parts to it including an engine that has been rebuilt but it's from an 89 so i noticed that there are 4 stator wires on the older engine and there are 5 on the newer engine can i just swap the stator in order to keep the newer...

I have a set of asr arms I'm getting ready to install them I just noticed they don't have grease fittings on them so am I supposed to use my finger and get some grease inside the bushings and reuse the grease seals or do they not need grease at all

So I just got done reassembling my engine did my leak down test and I got air out my vent line again so back apart with the clutch side and found that sleeve on the crank leaking I didn't put enough case bond on the inner part of the ring when I put it together so I cleaned and reapplied the...

I putting together a 240 blaster and Vitos wont carry the fat bastard pipe anymore so Im trying to find one

So i've been working on getting my blaster ready for spring and i'm looking to upgrade the front suspension. I'm gonna get a Diamond J kit for it and i've been looking for some YZF 450 front shocks but are kinda out of my price range for nice looking used ones but i found these do you think they...

Hey guys so it's been about 8 years since i last ran my blaster the reason i stopped running it was the old piston and cylinder were done, so finally i got around to rebuilding it i got a BBK for it had vitos install the sleeve in the jug and shes all back together and doing some reading on the...