Search results

After some rear hubs that will fit the blaster and give me the 110 pcd that makes it easier to get rear wheels :) Thanks a lot guys, remember im in UK but will be happy to pay postage costs from anywhere for the right price. :)

Universal Clutch Throttle Cable Repair Kit MX Enduro | eBay just thought I'd post this as havnt seen many people mention them, it's a kit with inner cables for both throttle and clutch. with an assortment of solder and solderless nipples at the fraction of the price for a new cable. handy...

so I'm gearing up ready to put the bottom end of my spare motor together and everywhere I look people are saying use the yamabond 4 or the threebond 1194, however in the uk this is proving difficult, there's one guy on eBay, selling a tube for 28 pounds, which is like 45 dollars just for a tube...

http://i1308.photobucket.com/albums/s604/J4M1E333/IMG_1604_zpsbd59d811.jpg http://i1308.photobucket.com/albums/s604/J4M1E333/IMG_1603_zpsbb36c526.jpg http://i1308.photobucket.com/albums/s604/J4M1E333/IMG_1602_zpsc444d82d.jpg...

Ive picked up my new quad today and its come with a keihin carb, As im use to using thumb throttles and personally don't like twist throttles, im looking to change it back, just wondering if i can use a standard thumb throttle and cable from a stock blaster or what i would need to order :)...

got myself some 2nd hand herrmann A Arms but they've come and the lower ball joints are bad. just wondering if there's anywhere in UK I can pick these up? Will be starting a build thread soon I:I

Hi all, Still having problems with the blaster smoking like a steam train. Was told the crank seals were replaced by previous owner, and it still smoked so i replaced the clutch side suspecting he didn't do it properly, and it still did it. followed advice on here and tore into it again...

Hi all, recently replaced clutch side crank seal on my stock blaster and it's still smoking like a steam train, i assume its the crank collar? or could it be something else? :-/ I've added the RTV to the chamfer of the collar and just waiting for time to fit it? is this likely to work? i was...

HI all :) First post for over 2 years :o finally managed to get hold of another blaster cheap, I:I As the title suggests i'm wondering how i can tell if the blaster i bought has been rebuilt as the owner stated? Im assuming that a compression test would tell? any other ways to tell...

im having a nitemare trying to locate the part above, i recently overhauled my clutch and when i took it apart it didnt have one, how important are these? and does anyone know where i can locate one over here in the uk? even better could someone take a picture of it, or link me to a...

Evening all, Noticed a small oil leak recently coming from the bottom of the clutch cover so thought i would undo it to see whats going on, when i went to undo it a couple of the nuts were lose, so i tried tightening them and they were just turning, im aware that the holes need re-threading...

As the title states my blaster is going through axle bearings in no time at all, some have lasted only a couple of hours after reading a few posts ive come to the conclusion that between the two bearings, in the carrier, should be a sleeve that the bearings tighten against which is missing...

Just finished a complete re-wire of my 05 blaster so thought I would share how I did it and what goes where seen as though there's a few rewire questions on here, one being my own :p firstly, all I have left is my headlight, the necassary switchs for this and kill switch on the left hand...

hi, just saying hello from north wales, UK. Got an 04/05 blaster, got a few weeks, no a little about quads so will always try help if i can :)

Hi all, im new to this whole forum thing so some constructive critism would be greatly welcomed!! I bought an 04/05 blaster a few weeks ago and used it on a field for a few goes, as it had a bottom end rebuild, it ran fine. today I took it out, I warmed it up as usual and then set off up the...