Search results

I did a leak test today and I noticed right away it's leaking out of the cylinder base almost all the way around. I wanted to check with you guys before I go throwing money at it. Should I try torquing it back to specs or do I definitely need to replace the gasket? Thanks.

I have a full rolling chassis with a complete engine that I Started to strip to paint the frame. Everything is pretty much there, wire harness and coil, no headlight though. The engine is off the frame but it's in great shape, shifts good. I don't know if it runs. I'll trade it for a decent full...

I just picked up a Husqvarna dirt bike and I'm trying to find out exactly what size and model it is. I was told it's a 430 but I'm thinking it could possibly be a 500, it's two stroke. I have the vin number if that would help, I don't have any pics right now.

I'm trying to do a leak test but not having any luck. I've got the exhaust blocked off and the leak tester inserted into the carb boot and tightened. I can't get it to pressurize. I could hear a whistling leak. I tore the stator off and found that the air is coming out of one of the holes behind...

I'm parting out one of my three blasters. The frame was cut to swap this Kawasaki engine in. From what I know so far it's a rotary valve Kawasaki 2 stroke, unsure of the size. It starts up good and runs good but I think it needs some tweaking. The choke was cut but if you pull the cable with a...

I'm trying to put a clutch cover back on with the kick start in it. How does the spring go so that it operates correctly? Also is it easier to do if I remove the lever first?

I have a swapped motor on my blaster, it's kawasaki. Has a hole in the top for a filter and the carb is inside on the right hand side under a cover? I'm trying to figure out what motor they swapped on there. I was told it was 2 stroke but I'm pretty sure it's 4 stroke, I haven't had a chance to...

I'll prob regret it but I decided to get rid of my honda crx. It's been a work in progress for too many years and I've lost interest in it. Just so happens that I made a deal to trade it for a pair of blasters. One was just rebuilt with a 240 big bore kit and the other one has a bike engine on...

I'm looking for a set of plastic scraps front fenders that have been race cut. I need the bulk of the fender intact if possible, like the main center mass of it. Thanks.

Hey guys I just picked up a mikuni 35mm flat slide carb for $40, is that a good deal or did I pay too much? It needs a throttle cable and an idle screw. Also is that too big for a stock setup if I was to change the jets? I'm hoping to get some engine work done so maybe I can use it later if its...

I'm looking for places to get parts chromed that accept orders online through the mail. I could search myself but I'm looking for places people have used before that are reputable. Any input is appreciated, thanks again guys.

Lightened Flywheel + tires/rims I'm looking for a flywheel and a 4 wire stator, I would prefer a lightened flywheel but anything in good condition. Also looking for someone who could possibly lighten a flywheel for me once I find a good replacement if I can't get one already lightened. I would...

Has anyone made or modified their own wire harness? I'm looking for the male and female single pin connectors with the rubber seals so I can fab my own harness or if anyone know what they are called. I haven't looked at my wheeler very well yet but I found a ball of wire what looked to be the...

I watched a video on how to sweat the bearings in...my question is will it work to put the bearings in the freezer or do you have to have dry ice?

Anyone have a good or bad experience with the hot rods or wiseco complete crankshaft rebuild kits? Also does anyone know if the stroker kit bottom end is compatible with a stock bore? I'm trying to decide what brand to get and if I can use a stroker kit without having to get the big bore kit.

I've been searching and searching and I haven't found anything on putting a 250r hood on the blaster. Has anyone done it, is there a diy guide? They have a wide variety of hoods for the 250r that I really like.

I'm looking to upgrade my video card but don't want to spend alot, was wondering what y'all recommend. Right now I have a Gigabyte gts 250, it's treated me well but I would like to upgrade into dx11 with something decent that won't break the bank. Not the most beastly specs but I built an AMD...

Hi I just bought my first blaster for $50. I'm new to them, it's my second four wheeler and second 2 stroke. I want to start rebuilding it but need to get familiar with it. I have no clue at this point if it runs, it's locked up and I'm not sure if it's the top end or what yet. It has a piece of...