Search results

I have been a member of this sight for around 3 years. To all the members here that have helped me through my build and with random problem especially awk08 2smoker85 Ken O'conner and everyone else that as given me advice, I know each of you as much as you know me which isn't much but that fact...

My blaster will not shift I was advised on here to replace the shift shaft and torsion spring, I changed them and no luck. I figured out today that it will cycle through the gears only if you spin the shaft the clutch is on at the same time you are trying to shift I really need help with this if...

I'm having a problem with the clutch on my wife's blaster not sure what she did but it will not got above third gear and it is hard to get back into 1st gear I'm not to familiar with the blaster transmission but sounds to me like she burnt up the clutch i drained the old cluth oil and replaced...

Ok so i blew a piston about 9 months ago then deployed to afghanistan i drained my fuel tank and stored my quad while i was gone i just got back replaced the piston then started the quad and it ran fine until i hit the throttle then it would bog down bad and die so i pulled the carb off and...

Ok so last weekend i took my wifes blaster out trail riding and it did great ran good and had no problems i didnt ride this weekend so on sunday i started mine up first kick let it start idling then went to start the onther one but when i went to kick it i had to stand on the kick starter and it...

The cap broke off my wifes coil on her blaster does anyone know if it will fire the same if I splice the wire because the coil is still good.

I finally got my Project started today and began breaking in the new motor I want to say thanks to everyone that gave me advice on how to do things through out this build to get it all together

I took my quads out Saturday I took my 4 stroke quad off the trailer let it run and warm up about 15 minutes put it in first tried to take off and nothing happened let out on the clutch all the way and it just set there until I nearly redlined it then it would go slowly and as it picked up...

After fixing my carb problem i tried starting it but it wasnt firing so i went to my other blaster checked to coil made sure it was firing brought it to my project ans still no fire put the coil from my project on my good blaster and no fire then put the good blasters coil back on the good...

I got ready to start the blaster today and the carb started pouring fuel out of the bottom overflow hose i adjusted the hook the needle sits on and its still flowing when i removed the carb to adjust the float when holding it uspide down at first when i blew on the fuel inlet hose a little air...

Alright this is my first build and i just got the engine together and ready to start connected all fuel hoses but i have one question while looking at the engine from the back on the clutch side just below and a little to the right of the carb there is a little nipple to connect a hose the...

So i found out i live 15miles from an active gold mining district ive been watching gold rush its got me motivated im going gold hunting i even bought a metal detector and a few marines that work for me got pans my wife says its ridiculous i told her she cant have any of the gold then

This is my first build i read the engine break in thread so im good with that but i just want to know is there anything i should check or do before i start it for the first time

i just read through a thread with good info by 4cfed but im new to 2strokes and i just got to the point in my build to start my engine for the first time but i havnt figured out how to do the premix yet what im asking is how many gallons of gas do i mix to 1 quart

Im going to get banshee hydros for my blaster this weekend i read a thread saying you have to weld a mount for the master cylinder is this true and is there a way around that

A friend is going to get one of these 2 quads and he asked me to help him decide which one to get so i figured i would ask the experts here are links to the ads HONDA 2005 ATV sportrax 2007 HONDA 450ER ATV atv

I found a banshee someone is Parting out on craigslist and i can get the axle both hubs and stock rims and tires with 40% tread all for 100$

Ok so i finally got to the point in my build where i was able to mount the engine once i mounted it installed the chain put the tranny in neutral without the clutch and it spun free while i was putting the chain on and once i put the chain on i tightened the chain tensioners then put the skid...

just to throw it out there i did do some searching and reading others threads and post before i brought up another reed spacer thread with that being said in all the reading ive done im having trouble finding what size reed spacer to get for my 34mm carb to clear the clutch arm can anyone help

I was on ebay looking for a vforce 3 reed valve but i found a few different ones and they all say vforce 3 for yamaha blasters and im not sure which one to get here are the links to each one any help would be great MOTO TASSINARI V-FORCE D... VForce 3 Reed Valve. YAM... YAMAHA 200...