Fares New Member Jul 1, 2016 6 0 23 26 Jul 1, 2016 #1 What is that washer looking thing in the stud there's only 1 of them on out the 4 studs Attachments image.jpeg 1.4 MB · Views: 329 image.jpeg 1.2 MB · Views: 331
M Markblaster Custom blaster Dec 6, 2015 2,311 760 175 Jul 1, 2016 #2 Service manual. http://www.blasterforum.com/threads...ervice-and-owner-manuals-free-download.17325/ Dowel pin.
Service manual. http://www.blasterforum.com/threads...ervice-and-owner-manuals-free-download.17325/ Dowel pin.
L Larry's Shee Active Member Technician May 23, 2009 9,271 1,057 149 Ortskaville, MI Jul 1, 2016 #3 Look at bottom of the cylinder, it could be stuck there. Why is it that many don't bother to clean the outside of the engine BEFORE taking it apart ?? SMH.
Look at bottom of the cylinder, it could be stuck there. Why is it that many don't bother to clean the outside of the engine BEFORE taking it apart ?? SMH.
Fares New Member Jul 1, 2016 6 0 23 26 Jul 1, 2016 #4 Larry's Shee said: Look at bottom of the cylinder, it could be stuck there. Why is it that many don't bother to clean the outside of the engine BEFORE taking it apart ?? SMH. Click to expand... It's not stuck in there what is the part number so I can buy them do I need all 4?
Larry's Shee said: Look at bottom of the cylinder, it could be stuck there. Why is it that many don't bother to clean the outside of the engine BEFORE taking it apart ?? SMH. Click to expand... It's not stuck in there what is the part number so I can buy them do I need all 4?
M Markblaster Custom blaster Dec 6, 2015 2,311 760 175 Jul 1, 2016 #5 Larry's Shee said: Look at bottom of the cylinder, it could be stuck there. Why is it that many don't bother to clean the outside of the engine BEFORE taking it apart ?? SMH. Click to expand... I was going to say something about that dirt also. Looks like a mix of dirt, oil, grease.
Larry's Shee said: Look at bottom of the cylinder, it could be stuck there. Why is it that many don't bother to clean the outside of the engine BEFORE taking it apart ?? SMH. Click to expand... I was going to say something about that dirt also. Looks like a mix of dirt, oil, grease.
M Markblaster Custom blaster Dec 6, 2015 2,311 760 175 Jul 1, 2016 #6 Parts catalog says 2 of them and both go on the same side. looks like you are missing one. Oh and stop making lots of threads about this same thing. http://www.blasterforum.com/threads/yamaha-200-top-end.64794/ http://www.blasterforum.com/threads/yamaha-blaster-dowel-pin.64802/ Last edited: Jul 1, 2016
Parts catalog says 2 of them and both go on the same side. looks like you are missing one. Oh and stop making lots of threads about this same thing. http://www.blasterforum.com/threads/yamaha-200-top-end.64794/ http://www.blasterforum.com/threads/yamaha-blaster-dowel-pin.64802/
L Larry's Shee Active Member Technician May 23, 2009 9,271 1,057 149 Ortskaville, MI Jul 2, 2016 #7 Markblaster said: Oh and stop making lots of threads about this same thing. / Click to expand... Why ?? More posts give opportunity to point out that the engine should be cleaned BEFORE you take anything apart. Reactions: jbuckster07
Markblaster said: Oh and stop making lots of threads about this same thing. / Click to expand... Why ?? More posts give opportunity to point out that the engine should be cleaned BEFORE you take anything apart.
Fares New Member Jul 1, 2016 6 0 23 26 Jul 2, 2016 #8 Ok I ordered a new set but if 2 are needed where do the 2 go
L Larry's Shee Active Member Technician May 23, 2009 9,271 1,057 149 Ortskaville, MI Jul 2, 2016 #9 The locating dowels go over the two studs in the right crankcase half.