I know,
but i could have measured this one like this with a popsicle stick, so i didnt bother diggin out the inside snap guages.:(
o boy
edited for future editing
O my bad, excuse me
I didnt know you were having a bad day and werent in the mood to get poked with a stick.
im sorry you didnt enjoy getting stick poked,
and i was mistaken on the name its not lahoya its DAHOYLE very nice fellow read up on it....
52s up front, I know it has been beaten to...
Anyways,,
Does someone have any good links to a how to rewind your own generator.
75 watts aint guna get it and i think i can do this one myself...
So are there any good how tos anywhere,,,,,
?
?
?
?
Maybe, Hmm, I think ill go look for one.
I dont know if it would brake any rules so no names, ive been on a few other "forums" and have dealt with the neverending BS of locked up felons who some how make it on the internet
Any body know who a Lahoya is, aint seem him here yet, bet it wont be long, 20,000 posts and not a dam project...
Still dont get it,
your going to
a stick a polaris engine in a 400ex
b weld a 400ex and a polaris frame halves together and put in a ???engine???
c put a 400ex engine in a polaris and weld a blaster frame onto the front
d put a polaris engine in a blaster frame??
e chop up a 300, a 400, a...
Where are you going to stick the blaster sticker so its forum relavent
or
get the haill outa here with that pos, go home you freakin snowmobile on wheels..........
:D:D:D:D:D:D:D:D:D
end of line
"so you wanna play that game hugh""
EDIT
Well we made need to take it to the private...
YOU"LL BE SORRY E
Do a wheely, climb a big hill, ride on two wheels, roll it on its side, start it in freezing weather, if that pump looses it prime your SOL
you have to buy gas AND oil anyways why not keep it all in one can?
How in the world did it do that?
The other case half not have a bearing or something??
That looks almost impossible!
That suckers really off in a hole aint it, good luck.
Here,
My suggestion for a knew owner of an old atv is to acquire a service rebuild manual, downloadable here somewhere?
Get a decent set of wrenches and sockets in metric,sears craftsman are decent.
Buy three specialty tools off ebay or elsewhere,
1 a stator flywheel puller ~20$...
Have a pic of it on the engine???
So this thang holds the chain down on the sprocket??
I thought they were some kind of ARMOR between the case and the sprocket to keep the chain from whipping into the clutch lever arm housing??
Damn, why didnt i think of this
well so far,,
Untrustworthy
to change mix ratio
Its ugly
Only stock 26mm carbs come with a oil port??
if you roll your bike over you have to reprime the pump!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
its ran by a plastic gear and plastic motors suck
theres electrical involved...
I think i might cut a notch in mine and glue them in with some indian head gasket shelauqer after i buff the rubber off the outside of them, "just in case"
Just remembered something
Theres another drain plug , see the flange head bolt forward of the shifter rod to the left of and down from the sprocket, has some twisty wire wrapped behind it,
That may go all the way through on yours, it does on mine, i dont know if its the same size as...
O man look at that hairline crack in the counter balance gear, and you ve got gear oil all over the clutch? Must have leaked out of the transmission you better get that looked at!!:D
There are a few passages inbetween the tranmission gearbox and the clutch housing area and theres also...
I have no idea,
More on the reed spacer, technically for us all
If its in between the reed and cylinder it does what vs in between the reed and carb boot??
Will a boyedson one peice, i quess its called a rad valve with the reed cage and carb snout all one peice, will it also need a...