Search results

Bought a ZR-440 chassis with some sno-pro Fox shocks on it a while back and had them all redoone, now I'm on to the engine. I was going to try and find an arctic cat LC 440 to toss in but I found a deal too hard to pass up! $50 and a 10min drive later I picked up a 1991 Ski-Doo Formula Mach 1...

My last one I got tired of bumping saying there would be progress and wound up not doing what I said, so I'm starting a new one since I'm actually starting to bring more parts in LOL What I'm starting with right now: Have a round house bearing carrier sitting here that I need to build a...

If any of you guys have been keeping up with my build thread you'd know that my knee got jacked up last spring. I had surgery on it at the end of July to repair my ACL and Meniscus (pics are about a week after surgery, right after they took the gauss off): Now i get to rock a pretty...

Looking to sell my Pro Circuit pipe and silencer. There is only that one barely noticeable dent on the bottom of the pipe, there is no rust on the pipe, just some dirt/oil and melted rubber on the end where the pipe/silencer meet up from my temporary coupler. If you want any more pics...

The snow is starting to fly here, so now the need to have my sled working better suspension wise is much greater than that of getting my blaster together. Sled is a Ski Doo Formula III 600, rear suspension is the C7 (dubbed the back breaker). The goal here is to make the sled much more...

If you guys have taken a look at my build thread recently you might have seen that i am putting a YFZ 450 front end on my blaster (in a nut shell). What i need help with is finding some stock shocks off pretty much any sport quad that are 17"~18" eye to eye. All they need to do is support the...

I know this isnt a computer forum, but maybe someone here could use these more than i could ;) ASUS Rampage Formula X48 LGA 775 motherboard - $120 shipped OBO Bought this thing new off Newegg on 12/7/2008, I have used this thing to house an overclocked E8400 @ 4.3 gHz with the Mushkin ram...

This is a bit of a feeler thread right now, but i want to sell my works triple rate shocks. The shocks were rebult before i got them and i myself only put about 4 hours of track time on them. These were off a banshee but the valving feels pretty good as it is. Shocks are in great shape, i will...

During my 4 month absence from here (mostly due to my knee injury) I picked up a new hobby, i have some friends that do it as well so i said why not. Well, a few months in and i have spent a good chunk of change on it already, lol. I have 4 guns now: Classic Army SCAR-L, Classic Army M4, Tokyo...

This is the last time this stuff is going up for sale, then its going on ebay. CEN Matrix Arena TR FRE truggy: Truggy is the stock FRE kit with some hop ups. Has the CNC upper bell crank, cross pin diffs, after market aluminum rear toe blocks (with inserts to change toe/antisquat), 17mm hub...

if you have a YZ 125 thats 2000 or newer i need the measurement from the crank case where the engine mounts to the swing arm and the diameter of the swing arm bolt. I would like the measurement to be made with a digital or analogue caliper (measurements to the nearest thousandth in inches)...

Are the fenders on the race hood farther forward than the stock ones? I could use a little more knee room while racing and was wondering if the race hood gives the room or not.

Got bored with my old one and i had this action shot from my last ride so i said what the hey, lets make a new sig! Started with this (original file size was 3648x2736 px): And ended up with this (original file size was 2000x1000 px): The resized version is in my sig :P Lemme...

Long story short, i got a 1991 YZ125 off a buddy. The thing is in poor condition, but im about to change that :P Since it was warm enough today, i finally got to work on the plastics. Got them prepped and a light coat of primer on them. They will be yellow when they are done (tank is going to...

I just got mine in today and i just realized i have no idea how to tie it into the ignition system, any help would be much appreciated!

has anyone ever used on of these before? I have heard that they are just keihin knock offs.

nvm, found what i was looking for!

I just officially kicked it off tonight. I have so far ordered a black gripper seat cover and a tether kill switch off ebay. Also on the way is some aluminum so i can tweak the nerf bars i have to work with my pipe. The quad is torn down to the frame. The intention of the build is to get it...

i see that most of u make them out of some kind of metal, well i decided to make them out of something different. I made them out of Polycarbonate. I will get some pics of them tomorrow, i did them a little different then what most of you guys do. The are still bare right now (had to try them...

My carb boot just tore on me, and i have a 34mm Mikuni round slide carb and a 38mm Mikuni round slide carb sitting in my shop that arent being used. Was wondering if i should just dish out for another stock size carb boot or go up to one of the bigger carbs. I plan on getting a factory 7 pipe...