Search results for query: Led lights

OEM lighting is AC, you'll need to change it to 12v DC for LED lights & accessories. That takes a rectifier/regulator, small battery & float the ground. There are threads here describing this in detail. Also wiring diagrams. Just use search. Happy night rides! 🍻...

...your lighting system it runs through the rectifier regulator where it is converted to 12V DC. The flickering is due to the voltage drop at lower RPM falling below the threshold the LED lights require to illuminate. Best way to address that is as stated above, adding a small battery to the system.

Otis' Hot Rod Blaster It began as a 89 Blaster. We've owned it about 20 yrs. Played with brakes, suspension & engine stuff from the start. Put a YZ250WR engine in it around 07. Bf BOTM August 09. Switched to methanol at some point. That was entertaining. Took it apart to reconfigure the...

...if you know your blasters you know how much they need it) a full-on electrical system with a battery and a rectifier to charge it and LED lights on a switch all around. This thing is loud and angry and needs an experience rider. Really, no BS. Compression is 160 and this quad is a ready to go...

I have no let switch and no headlights but I'm trying to find out how to put an led bar on my blaster I'm not worried about mounting I just dont know what wires to hook up to what and how to use the high/low/off switch when hooking it up

Definitely not the stock carb. It didn't come with an airbox lid. The 270 I thought would have been around a good starting place since stock is 230, but no harm in swapping up. I cannot wait until it runs well enough that I can start doing plug chops! I had planned on putting an LED pod in...

...it running better, I'd immediately do a "plug chop" to establish the correct main jet size. If you plan on upgrading to a DC system with LED lights, then suggest getting the Rick's Motorsports (not Ricky Stator) upgrade for your stator. Optionally, I recently did the DC conversion and have...

My blaster built in 2004 has a switch on the foot brake with a connection to the wiring harness, but this has no function. I'm considering swapping the ignition lock for another one with multiple connections to disable all electronic consumers. Conversion to LED lighting is planned anyway...

This isn't an exact step by step DIY but all the info is in there........... https://www.blasterforum.com/threads/converting-to-led-lights.58577/

...I have gotten from baster forum. I've put in a new clutch, 400ex back shock, tors delete, parking break delete, oil pump delete, new stator, coil, cdi box, front end barrings and bushings, jets, and new led lights I run off a battery. Just wanted to say hi to everyone and thanks for all the...

okay it won’t let me upload the photo but there is like 4 earths into one going to the rear light

So I recently fitted a brake light back onto my blaster as previous owner kicked it off and didn’t need it. Used a Lucas style 12v 2 filament bulb style no LED. Wired it up and I can either get a bright tail light (which should be brake light) and when brakes applied all lights go out. Or I can...

...i have a aftermarket bumper as-well as 3 inch spacers. I do a-lot of trail riding and some flat track, so i would want some hand guards, led lights(front and back) rear grab bar, shock covers, nice shocks, sprockets, as-well as maybe one of the old front plastics, and any other cool designs...

https://www.blasterforum.com/threads/converting-to-led-lights.58577/ This may help you

I have a 2000 blaster that I'm trying to put a Blazer 4in light bar on. So far I have the light hooked to the high beam wire and just grounded on the voltage regulator. It worked fine for a few seconds but now only the bottom row of lights come on and are hardly visible. Would putting a...

...Replaced w a slotted caltric stator. Floated the ground on it, ran new wire. I followed the diagrams found on here. I did this to add led lights and tail/brake since none on the machine. Also replaced magneto and key. (also have the trail tech reg/rec w battery set up). Got our spark back. I...

Thanks do I run my coil off the reg rectifier or leave that connected to ac voltage, I am only using the lighting circuit wire (yellow) to send ac to the reg/rec should j use the black and red power wire for the coil aswel? , Thanks

Pretty sure you have to float the ground to add a reg/rec, meaning to un-ground that wire at the stator and run it directly to the ground of the reg/rec skip thru this thread and check all the tech posts... https://www.blasterforum.com/threads/converting-to-led-lights.58577/

check Bronco's journey thru this, but there has been others just hook them up to the existing AC voltage system, they'll dim at low rpm's and possibly blow out, so don't do it to expensive ones ..... https://www.blasterforum.com/threads/converting-to-led-lights.58577/

How do you wire up an led light bar to the new model of the Yamaha blaster