Search results for query: Won't shift

So I am rebuilding this 02 blaster and it won't shift past second . I have good shift forks good shift cam and a good transmission I is a split case as of now I have tried everything but can't figure it out I have read all the transmission forums on here with no luck

Hi Gurus, I'm going to help a buddy out and see if I can repair his gen 1 Blaster. He's dropping it off tomorrow. What I know so far is that it used to run great then started not being able to go into first gear (just skipped it). With that issue he would use 2nd on up until it stopped going...

Make sure shift star is turn so it alines with notches in the case. Otherwise it Will hit case. And halves won't go together. If crank was left in stator side Case. And no damage to that half and everything us clean you can leave it in. Stator side has an interference fit between crank and...

If you didn't already check your throttle cable and where it connects to the thumb. Its adjustable there and at the tors bolt. Some times the bolt gunks up inside and won't make contact but will feel bottomed out. Carefull they break easy. You can make the quad idle with just the adjustment on...

Good answer. As to the power band , it will have unbelievable bottom end, but just as you expect that two stroke smile, it stops pulling and you HAVE TO shift, it won't rev any higher. I actually posted a thread like this 5-6 yes ago.

Just recently did a full engine rebuild, now I'm having an issue with the clutch cover. If I install it and torque to specs I can't kick start it, kick start won't move at all If I leave the bolts loose it kicks fine. If I take the kick start gear out and put the cover on it sits flush with the...

Not quite sure what you mean by won't shift past 3rd. As in actually just won't manualy shift past 3rd .? Did you split the cases? List what work was done to it. Should help us narrow it down for you ok. So we can figure this out and get you up and running

just got my blaster and put lots of work into it now ats it won't shift past 3rd .runs great and had no problems before.any answers?

Fresh engine. Cylinder ported for it's intended use. Head mod. Shift star mod for easier shifting. Good handle bars that won't break is a must. Light rims and tires. Gearing. The most expensive is going to be suspention. That is going to make or brake how fast you can ride your bike around the...

Was the shift star bolted on or welded on? If bolted on. Was the locating pin installed Pryor to bolting on star?. Dum question but is shifter tight?. You may have to drain the oil and pull clutch cover to investigate.. Take some pics of shift shaft and shift star area . maybe we can see...

Hi guys, I'm new to the blaster forum and decided to finally make an account because maybe I could get some help. I recently completed my first full rebuild on my 05 yamaha blaster. After putting it back together it fired up and sounded great, but when I tried to shift i hear the click but the...

Haven't had time to check but ill look this weekend and yes its only 4th gear that won't go in

I did replace the case and put on new gasket

Have a 2001 that I picked up a few weeks ago, was having some carb issues when idling and I replaced the carb, ran way better still need to fine tune it to see what it likes. When riding it going to shift up something came loose had to push it home, found that the clutch and basket had come...

As mentioned, fix the air leak first. A runaway engine can self destruct in short order, measured in seconds. IF this happens and the kill switch doesn't stop it, pull cluch, shift in gear, hold brake, dump the clutch. At this point it has gone into "autoignition" and even pulling the plug...

...exactly what the ring is called I believe a spanner ring isn't in the proper place (I believe its the second one in the clutch basket) it won't shift I learned the hard way. Then also theirs the shift rod which has a ball bearing behind it that can roll out then no shift. But if really had...

Remove air cleaner boot and visually check that the slide isn't hanging up. Another cause of wide open throttle is a crank case or seal leak. I highly recommend a leak down test. I wouldn't start it until you do. A leaking seal or crankcase can cause a runaway engine where the switch or key...

Just bought a 98 blaster, starts right up but I can't change into any other gear or into neutral. Any information on how to fix this would be much appreciated.

Just purchased my first atv (2003 blaster) and I noticed the shift lever kept popping out of first or won't even go into 1st gear. It seems to slip out a lot and I tried tightening the screw that holds it in but it doesn't fix the problem for more than five minutes. Does anyone have an idea at...

...atv(99suzuki 250quadrunner), it now will hardly shift. I literally have to stand on the shifter to make it change gears, and sometimes it won't shift at all. I think it may be either he burnt the clutch out, or messed up the shift forks. Just wondering what everyone thinks it may be so I can...