Search results

I have brand new Boyesen Super Stock reeds for sale. They were taken out of the package but I ended up going with Vito's dual stage. These have never been installed. $13 shipped Also have a TMS helment. Size XL with visor. Wrapped in faux carbon fiber vinyl. Worn twice. Comes with a...

Well, I'm sick of living with my mother in law. It's time to sell the toys and save for a house. Details: 1995 motor and plastics 2003 Frame Fully titled and registered in Iowa and has current Wisconsin ATV Pass 2003 Rear Shock Razrs in the rear 80+% tread Stock tires in front <50% tread Vitos...

Ok, long story short, I went ahead with replacing my crank seal due to it revving out at idle after it was warm and milky crankcase oil. I broke the inner hub in the process so I bought a new one to replace it. This meant taking the clutch plates out. I got it all back together, adjusted the...

During my crank seal replacement I messed up my clutch boss. Looking for a replacement. thanks

Looking for a rear grab bar. Not looking to spend much more than $25-30 email works best, thanks chad.harwick (AT) gmail [dot] com

I just purchased a 7 piece oil seal kit. I have no clue which seal goes where. Is there a tutorial on this forum that I'm missing? thanks

I've run into some issues. My wife and I are moving into our mother in laws house until we find a house to buy. We need some extra money and this has to go. I have forsale a running and driving Blaster. 2003 Frame Fully titled in Iowa (No need for you to fight with the DNR about getting it...

I've been trying to track down an air leak in my system. I've narrowed it down to the top of the carb. I took the top cap off and there is a very thin paper gasket in there. Is that all that is keeping the air from getting in? Can it enter from where the throttle comes in? thanks! I:I

Looking for a stock reed cage with reed stoppers. No reeds needed. thanks I:I

I need a set of bolts for the plastics and tank. I'm having a hard time getting what I need at Lowes. The previous frame I had the PO drilled out the holes and did a bolt/nut and I just want to run the bolt like it should be. Thanks

I accidentally threw away the metal bracket that holds the clutch cable to the engine. I need this as soon as possible. Please pm me if you have one. This is one of the last pieces I need to get my blaster at least driveable minus my brake issue. thanks!!! I:I

Ok, I've been searching quite a bit this morning and can't find much information. I had a bent up frame on my 95 so I bought an 03 frame. I knew the brakes were different from the get go. How can I do a rear cable setup on an 03 frame? It seems the cable is way long too. How have...

Looking for the items in my title. thanks!

Hey guys, Looking for a favor. I found a really good deal on a small trailer. I've been looking for one for a long time now and saw one pop up on Craigslist this morning. Can someone give me the measurements length and width of a stock blaster from the bottom of the tires? I won't be home to...

I think there should be a sub-forum in the engine section to put all the stickies. Engine - Yamaha Blaster Forum Just make an FAQ/Sticky subforum.

So I rebuilt my carb last week with the kit from Rocky Mountain. Everything went well in that area. I took the reeds out to inspect them and the intake gasket got ruined (3JM-13621-00). I figured I could just use gasket maker on it. The first time I tried to start it, third kick and it...

I'm looking to get into some trail riding this spring. I'm always scared about running out of gas. Two questions. 1. What you are you guys doing to carry a small cooler or gas can? 2. What do you do for gas on the trail if you don't carry? Do you keep some oil under the seat and mix in...

I think signatures should have limited picture sizes in them. chad I:I

I hate to post, but I've exhausted myself searching about this. I've been having trouble starting. So I decided to get a full car rebuild kit and put new reeds in while I was in there. I popped the cage out and something just didn't look right to me. According to the blaster manual and all...

Here's my deal. I bought a blaster for 550 bucks from a guy that was moving. Ran good on the test drive, and never did good again. The guy disappeared. I've been working on getting it back into running shape. After closer inspections I noticed the frame is cracked in a few spots. I'd much rather...