Search results

  1. Awk08

    clutch not enganging

    dots on pressure plate and basket aligned ? 1/4" is alot for movement, just needs to release pressure
  2. Awk08

    Do not order from BikeBandit dot com

    https://jalopnik.com/motorcycle-parts-seller-bikebandit-has-stolen-646-000-1848823954/amp?fbclid=IwAR37wBL6WYdWqbE0zVtsmb2C374hJYTZGMQoXzw4Af_3XoHB_-rHM7kw8ow
  3. Awk08

    Carb Float Adjustment

    everything you need is in these 2 posts, if that doesn't work I'd suspect you need a new float needle and seat. https://www.blasterforum.com/threads/float-heights-and-how-to-adjust-them.50565/ https://www.blasterforum.com/threads/easy-and-almost-free-way-to-stop-leaky-carbs.33335/
  4. Awk08

    Need options for more power/performance

    You should have had Ken port that cylinder and modify the head while he had it for the bore, that's where the power is, you know the # :) and nothing makes you faster in the trails than suspension, all the power available is no good if you have to slow down for the rough stuff.
  5. Awk08

    Stator conversion to battery charge

    This isn't an exact step by step DIY but all the info is in there........... https://www.blasterforum.com/threads/converting-to-led-lights.58577/
  6. Awk08

    Vitos 28mm carb jet suggestion

    guaranteed no vito's or any other carb comes jetted for 10 degrees look in this thread and find what others running a 28mm mikuni are running, then go up 2-3 sizes to compensate for sub arctic temps........... https://www.blasterforum.com/threads/what-jets-are-you-using.28981/ plug chop to confirm
  7. Awk08

    Carburetor

    Stick with the stock carb for those mods, you'll need main jets 270 thru 310 for the FMF, start large and plug chop down after the proper heat cycles and break in search in the carb section for how to plug chop the main jet, the stock pilot and middle clip on the needle settings will be good
  8. Awk08

    Heat marks on crank

    That's common from the factory, run it
  9. Awk08

    Ignition Coil

    Any of those will work the same as the stock coil
  10. Awk08

    Carb size

    A stock carb will work best for that build, tune for you mods with plug chops
  11. Awk08

    Blaster revs up after I give it gas and stays revved up in neutral

    Carb slide or cable hanging up, or air leak < that'll make it go boom, search in the carb section for testing airleaks
  12. Awk08

    For Sale: 2000 Yamaha Blaster $1600

    I'd say that's too much, but heard prices have gone up ?
  13. Awk08

    01 Blaster FS

    I think you need 2 or 3 different people to "like" your pics or comments to open up your ability to post, this helps us keep spammers from posting spam links or porn then go to the home page, look down thru the sections and choose a section that best fits your needs .... engine, tires, body...
  14. Awk08

    Oil Injection Question

    you can't run both injection and mix, it would have to be running like poo and probably fouling plugs ? and you also cannot run it with the line off the carb, unless you blocked it off ? it was a severe air leak. you're this far, just delete the injectionm block off the nippple on the carb with...
  15. Awk08

    Problems with my blaster

    Yes, you actually have to remove the clutch and stator covers to spray around the crank seals for a suspected leak, if no other exposed leaks are found
  16. Awk08

    Problems with my blaster

    Follow the TORS delete exactly..... https://www.blasterforum.com/threads/how-to-remove-your-tors-03-06-models.41973/ and check your reeds
  17. Awk08

    Comment by 'Awk08' in media 'Alternate view'

    @blastorious what brand of nerf bars are those? ...... XFR Pro Peg Alba racing and Pro Armor also make nerfs with built in heel gaurds check ebay or those websites
  18. Awk08

    Where to buy a quality carb rebuild kit and float

    Ebay from Vito's, you'll need to search and buy a float separately but they're on there https://www.ebay.com/itm/142549507570?hash=item21309cddf2:g:e70AAOSwZzlgW2l0
  19. Awk08

    Jug base gasket

    You don't have to replace the head gasket if you anneal it before reinstalling......... Do 3 heat cycles,, I never used a temp gun but until I couldn't hold my hand on the cylinder for more than a few seconds without getting burnt, after the 3rd heat cycle/cool down, retorque the head and...
  20. Awk08

    Oil Mix question

    A plug can foul instantly if oil gets up inside between the electrode and insulator, try another one. we like the non resistor B8es over the Br8es plugs that only limit radio interference