Search results

  1. 2

    engine locked up need some advise

    I used a motion pro puller that was designed for the blaster. I'm not sure what lapping the flywheel is, I just lined up the slot on the flywheel to match up with the woodruff key. I ordered a new magnet and screws off eBay for the flywheel, and a new top end gasket set. Hopefully I'll be...
  2. 2

    engine locked up need some advise

    So i pulled the flywheel off this morning and 2 bolts that hold the magnets on was broke and the magnet was damaged. Not sure what would have caused this to happen. I just had it off to install a new woodruff key a little bit ago so maybe it cracked and broke when i reinstalled it. Thanks for...
  3. 2

    rear shock questions

    I was going about adjusting it the wrong way. i was just confused on how to adjust it, thanks for the help.
  4. 2

    engine locked up need some advise

    so it has been a bummer of a day... ive had my blaster running good after a complete ground up rebuild, I ran the blaster today and it stalled. I then tried to kick it and it the kick starter stuck. so far I have pulled the clutch cover and checked out everything there and it looks like its...
  5. 2

    rear shock questions

    I have a 250r rear showa shock, and i think it needs a rebuild/revalve for my weight (225). when i sit on the blaster it sinks about 4-6" in the rear, is this normal? It still has shock travel but it does not. Under hard acceleration the rear sinks alot more and the front tires almost come...
  6. 2

    finished my blaster build

    Picked the swing arm up on ebay used with chain for about 200 bucks. It looks like its one of the 350 dollar ones that you can get new on ebay. Then i had to use a pipe to extend the rear bumper. The rear bumper is a dg alloy bumper.
  7. 2001 red blaster

    2001 red blaster

  8. 2

    finished my blaster build

    Here is some pictures of my finished blaster rebuild https://photos.app.goo.gl/YLXjCABSenmsLNdA8
  9. 2

    Thoughts on a vitos 240 kit for my trail bike

    So my current mods are +4 swing arm ASR a arms 250R rear shock YFZ 450 Worx tipple rate front shocks Banshee Rear Axle Vforce v3 reeds Project blaster Air filter box with Uni Filter, open top 30mm OKO Carb (not sure what jetting) FMF Fatty, Power Core 2 The bike runs good without issue...
  10. 2

    HELP my clutch is stuck!!!!

    the friction plates could be stuck to the steel plates in the clutch, you might need to disassemble the clutch and help them unstick to each other.
  11. 2

    clutch arm adjustment picture request

    So i went ahead and disassembled the clutch. some things i noticed is that it looks like it was assembled in the wrong order. the spring was installed first. IIRC this is installed 3rd. Also all of the friction clutch plates were stuck to the metal plates. almost like they were rusted...
  12. 2

    clutch arm adjustment picture request

    It was all of a sudden when the clutch quit working but I'm guessing it's because the lock nut on the adjuster arm came loose
  13. 2

    clutch arm adjustment picture request

    So today I took the clutch cover off and I could turn the locking nut on the adjuster arm by hand It wasn't even snugged up or anything of now tried pointing the clutch arm towards the mark on the engine and tightened the adjuster arm up to where it holds it in that position but I'm still having...
  14. 2

    clutch arm adjustment picture request

    So my blaster has no clutch at all, and i think i need to adjust it. I've read the manual and understand how im adjusting it, but what im not clear on is do I rotate the torque arm counter clockwise until the arm arrow is pointing towards the marking on the case. If anyone has a picture of how...
  15. 2

    GSXR swap issues

    So the issue was the angle of the master, stops on a dime now Thanks for the help
  16. 2

    GSXR swap issues

    That helps, several of those show the master Bing much lower down on the frame than mine so I think that's my issue. I actually have a bent 03 frame laying around so maybe I should just cut off the bracket on it and we'll that on.
  17. 2

    GSXR swap issues

    Does anyone have some photos i can use to to compare to mine? Most of the threads on here seem to have dead links. i'll get some pictures up tomorrow morning
  18. 2

    GSXR swap issues

    I have it hooked to the peddle, I'll snap some.e pictures later today, it's not perfect ly straight but with it making fluid come out when I was bleeding it I thought it was straight enough
  19. 2

    easy wiring diagram for you

    Thanks I just wanted to message you since you built the kits I figured you would have seen my issue at one point.
  20. 2

    GSXR swap issues

    Gave this a try and it definitely helped, now it will squeeze the disc some but it seems like it's not stoped it like it should. It will still roll down a hill if have the brake pressed, it seems like maybe the master is not going all the way in. But I can't press it any further by hand.