Search results

  1. Spencer Evans

    Clutch adjustment

    Thanks for the reply, I actually found what was wrong in the transmission. One of the shift forks was messed up, thankfully it didn’t do any damage. Replaced it and it ran great through all the gears so it’s getting it’s very first real ride tomorrow, it’ll be my first time riding a blaster
  2. Spencer Evans

    Clutch adjustment

    Not sure if anyone will read this in time, but I figured out it was something in the transmission so I split the cases again.. everything seems fine is there any videos out there on assembling the transmission the right way, just want to make sure it’s right
  3. Spencer Evans

    Shifting issues

    Hey man I have the exact same thing going on, I know this is old but did you figure out what it was
  4. Spencer Evans

    Clutch adjustment

    I took the clutch plates off and the center hub spins even in neutral, what does that mean?
  5. Spencer Evans

    Clutch adjustment

    im sure there is a thread like this somewhere but I couldn’t find one. I just put in new clutch plates, cable and perch/ lever. I bought this blaster used and rebuilt the whole motor so I haven’t actually rode it yet, but it starts.. everytime I put everything back together it works fine in...
  6. Spencer Evans

    Clutch problems

    Stupid mistake, just installed it wrong.. didn’t line up the dots, I use 10w 30 oil any recommendations for the oil, might switch to atf after I get new plates
  7. Spencer Evans

    Clutch problems

    hey everybody, I recently rebuilt the whole bottom and top end on my blaster and have just finished leak down testing and it finally runs right. Only problem I’m having is when I go in gear the clutch seems to always be engaged. It jumps forward and you can feel the transmission click, but the...
  8. Spencer Evans

    Left seal

  9. Spencer Evans

    Left crankcase seal

    Hey finally got the seal out and got new ones, I’m not sure which seal is for the left side, one is bigger than the other when comparing the right and left case seals. Maybe I installed them opposite of what they are supposed to be.. thanks again for the help!
  10. Spencer Evans

    Left seal

    I have both the right and left, one is bigger than the other
  11. Spencer Evans

    Left seal

    Hey everyone just trying to figure out which is the seal for left side of the case, I’m second guessing myself and need the right answer, I’ll try taking a picture. Thanks!
  12. Spencer Evans

    Left crankcase seal

    I made the mistake of not putting any grease on the seal, which I found out later isn’t very smart.. it came with the bottom end kit I bought (hot rods) . It was a bad enough air leak that it wouldn’t start, but the crank is brand new hasn’t even run yet.
  13. Spencer Evans

    Left crankcase seal

    The crank is still in, just rebuilt the bottom end and the seal that came with the kit wasn’t doing its job.. tried screws maybe I’ll just have to get another tool. Thanks
  14. Spencer Evans

    Left crankcase seal

    Trying to replace the seal on the left side of the case but having trouble removing it.. have tried just about everything other than buying a tool, it seems to be really stuck in there. Thanks for the help!
  15. Spencer Evans

    Air leaks

    Thanks I’ll ask him
  16. Spencer Evans

    Air leaks

    Hi everybody, I just got done rebuilding the top and bottom ends on my blaster. I finally got it started today after having to use starter fluid, but it immediately revved out. I set the carb back to the settings from the manual and it still happens so I’m guessing I have an air leak. I...
  17. Spencer Evans

    Broken bolt in crankcase

    I ended up getting the remainder of the bolt out but the threads are bad, hopefully a shop doesn’t charge too much to tap it because Im trying to save this case
  18. Spencer Evans

    Broken bolt in crankcase

    This is a picture
  19. Spencer Evans

    Broken bolt in crankcase

    I just replaced the bottom end on my blaster and broke off the bolt that goes into the spring and stopper lever on the end of shift assy. Any ideas on how to get it out, I’m beyond frustrated