Search results

  1. Oh4Blaster

    WTB: extended swing arm

    Looking for an extended swing arm. If someone is parting out a blaster and has a +2 or +4 swing arm or has one to sell pm me.
  2. Oh4Blaster

    Setting works shocks

    Does anyone know how to set the top rings on works shocks? I can’t find a clear explanation on how to set the rings. Any help would be awesome.
  3. Oh4Blaster

    Front progressive shocks

    Hey guys I have a set of these sitting around that maybe someone can put to use. I switched over to works dual rates and love every minute of them lol info will be in the link. I will ship them if buyer covers the cost to ship two shocks...
  4. Oh4Blaster

    Looking for stock carb or bigger for my blaster

    Hey guys I’m looking for a stock carb for my blaster or an upgraded one. Located in NEPA outside of Wilkes barre and Allentown. Pm me and let me know what you have.
  5. Oh4Blaster

    400ex thumb swap

    I know it’s been covered before, but I’m going to give my honest opinion on the swap. First and foremost it’s a very simple swap, except for getting the cable to sit right in the arm. First take off your right grip and if you have odi lockons it’s a 2.5mm Allen key Second unscrew the top of...
  6. Oh4Blaster

    Rusty Pipe? NO PROBLEM, Cleaning rust with aluminum foil.

    Dude you have to try using a wire wheel and the product zerust axxaclean. Wire wheel the rust off, coat the pipe in the axxaclean, I used a green scotch bright while the cleaner was on but you can skip that step if you choose, then spray it down with water, give it a polish and enjoy your results. ✌
  7. Oh4Blaster

    Air in fuel line. Driving me nuts!

    Well here’s my report lol. I threw in my 290, had it fire over and then it died. Had some hope after that and then got fed up. So then I shocked myself checking for spark, I know that’s there only thing left was to check my compression and after 5-6 kicks wide open and the needle staying at...
  8. Oh4Blaster

    Air in fuel line. Driving me nuts!

    im running a clear hose, but im thinking my problem is due to jetting because it only craps out at like close to 3/4 to full pin. i have back up jets but im not too sure which to throw in. im at 280 now and have a 290 and 300 on deck. my mods are bore .20 over, vforce4s, no box lid, tors...
  9. Oh4Blaster

    Air in fuel line. Driving me nuts!

    Hey guys I can’t seem to find out where these air bubbles are coming from causing my blaster to run like a pack of dog turds. I’ve sat there purging the line and used a 1/4 tank in the process. Cleared the line up so I thought, took the bike for a ride and it was good for about 5 minutes and...
  10. Oh4Blaster

    Air in fuel line. Driving me nuts!

    Hey guys I can’t seem to find out where these air bubbles are coming from causing my blaster to run like a pack of dog turds. I’ve sat there purging the line and used a 1/4 tank in the process. Cleared the line up so I thought, took the bike for a ride and it was good for about 5 minutes and...
  11. Oh4Blaster

    2003 blaster wont start

    Hey man I was having a similar problem with mine and it turned out to be a stripped main jet thread where it screws into. The needle sits in there above that, but since the threads were stripped it wouldnt allow the jet to sit properly and it was leaking too much fuel when demanded on top end...
  12. Oh4Blaster

    Quad is having problems at full throttle

    Hey guys the problem is fixed. It turned out to be some with the jetting and that brass piece the needle sits in. I had a shop look at it and they found that the main jet was hard going in and wouldn’t seat all the way. The threads were also messed up where the jet screws into which was letting...
  13. Oh4Blaster

    Quad is having problems at full throttle

    Blaaster thanks for that info. I actually called vforce and spoke to a tech to see what they would recommend and I was told 280 would be fine with my setup. I’m going to mess around with it tomorrow but want PA to warm up already so all this work isn’t done for no reason lol
  14. Oh4Blaster

    Quad is having problems at full throttle

    Alright guys I narrowed it down to a jet problem after blowing through a brand new box of plugs +2 more. The diodes are black as night. I took the carb off and like the manual said check the main jet and it’s stamped 260 and everything else is set to the fmf specs but I’ve added VForce4s and...
  15. Oh4Blaster

    Quad is having problems at full throttle

    Hey guys, I’ve been trying to track his damn problem down for weeks and it only seems to want to stick around. My quad is having problems getting to full throttle. As soon as you mash it to take off it bogs out at the top of every gear. Other than that the quad will kick 1-2 kicks, idle fine...
  16. Oh4Blaster

    Hey hey I’m new!

    Hey guys what’s going on? I’m new to your forum, but not new to forums in general. Just came from a long run with 240sx’s and now it’s two strokes all day. Lol first time owning a two stroke and always wanted a blaster and all I can say is I’m glad I got out of drifting and got back in the...
  17. Oh4Blaster

    WTB: Extended axle

    it was me lol I’m about to go scoop it up from the post office. I was not passing up that price for a dominator axle.
  18. Oh4Blaster

    WTB: Extended axle

    Yeah last night, but I wanted to find one on here but that axle is reasonable and it’s close enough for me to pick up if decided. Thanks for the find.
  19. Oh4Blaster

    WTB: Extended axle

    Looking to find an extended axle for my 04 blaster. Msg me with what you have. I will need it shipped to 18224
  20. Oh4Blaster

    ISO: 03-06 rear carrier

    That’s man but I ended up finding this super sweet atv parts recycler in my area and the dude had shelves lined with carriers for the blaster. Finding the one I needed was an adventure. Also if anyone is curious and lives in nepa or around there the place is called Milwaukee cycle service.