Search results

Ok guys. So ny clutch wasnt working so i pulled off the cover and the push road wont budge. i tried everything to get it out. then i took off the actuator and i could see the rod down the hole had like a big lip on the outside of it stopping it from popping out. Had anybody any eay if getting...

Ok guys. So ny clutch wasnt working so i pulled off the cover and the push road wont budge. i tried everything to get it out. then i took off the actuator and i could see the rod down the hole had like a big lip on the outside of it stopping it from popping out. Had anybody any eay if getting...

Its a koso carb but it was doing the same thing with 5my old carb aswell

Ok so this is my first blaster and my last one. Problem after problem with it. I have never got it running right Nd even still woth a different engine it's still not running. Ok so I bought a second hand engine a vitos 240 is has 135 140 compression. When i got the engine I put it in and it...

Thanks for the reply I can get fluid all the way up to banjo bolt that goes into the master cylinder but it just can't get fluid into the master cylinder. I have a sunction gun and tried using that bit all that does is build up pressure pulling the fluid that in the pipes out and still the...

I got the back one does. Had to tske master cylinder off and pour fluid down the banjo hole. Can't get the from master cylinder to get the fluid put . I had tried everything

Ok so after putting my bike back together. I can't get the bloody breaks to bleed at all. I tried a vaccine tool to try and pull it through and also pushing it through. Also I tried the syringe and hose. The fluid won't go past the bleeding nipple no matter what I do. I can't understand this at...

So after taking the pipe off I put the bike upside down with the exhaust port facing the ground. Immediately I could see the fuel coming put and after about 15 mins I tried to start it again and went right up.

Could I not take of speak plug and turn the motor upside down ?

Thanks man. Appreciate it. If that doesn't work any other way?

Ok so after many problems with my vlaster I finally nearly have it right. It has around 143 psi. I got a second hand engine with a vitos 240. Put it in my own frame wires it all up and it started first kick left it ticking over for a few mins shut it off and I seen gas coming from the carb. Now...

Thanks my friend. There is nobody around me to fix these.i live in Ireland. Thanks for your information. I think it right about the Chinese cylinder. My old cylinder is in bits but I'm going to buy a second hand oem . Thanks again

Hi. Thanks for reply. I bought a rebuild off ebay like 2 months ago and that kit didn't last to long. So this time of decided to buy all weisco parts. Don't you hone the cylinder to make circular groves to hold oil to lubricate the piston rings. Sorry for posting so many things but this atv is...

Thanks for the reply. Any idea what would cause this. I honed the cylinder to before I installed the piston. It's dead on 100psi. Mabey when the rings are broken in the compression will rise ? This had me baffled.

I was just looking at it there and the seal does go all the way around the crank. Should it ? It's about half inch away for the crank?

Hi guys. I just rebuild my whole motor and I done a compression test before I run it in. It has a 100 psi. This is woth a fresh jug,piston,piston rings crank seals and bearing. Is this a normal reading for a freshly build motor

Hi I'm just after doing a full rebuild on my blaster. Just before I installed the flywheel I blew into the Intake port and I could feel air coming through the case by the crankshaft on the flywheel side. I don't think it's supposed to that is it ? What would cause it to do that. It got all new...

Hi I'm going to get my head rechamberd and I need to know how much material I will need to remove

I'm looking for a milled Yamaha blaster head that somebody would be willing to sell ?

thank you so much my man. Just what I was looking for