Search results

  1. Tooloose

    Do I ride it or keep it stored?

  2. Tooloose

    Blaster runs for a couple seconds then bogs and dies

    Find a working TORS system and reinstall it! Remove peacock on tank and clean it, so that fuel supply from tank to carburetor flows freely when it’s turned to the On position and reserve both.
  3. Tooloose

    engine won't take any adjustment

    You have an air / vacuum leak! Consult AWK he use to build a vacuum leak test device.
  4. Tooloose

    Please tell me there's a chance kick start being locked doesn't mean bottom end...

    Seized top ends are quite common especially when it’s 32 degrees or colder. Not allowing cylinder warm up during extreme temperatures can cold seize of the piston in cylinder in winter. I know, my oldest son and a friend locked up my blaster on a cold day years back along with using alcohol...
  5. Tooloose

    HELP!!

    Clean your carb, reset float height to factory specs(level). Flush tank and install new filter inline to carb with arrow on filter pointed towards carb. Set mixture screw on carb to factory specifications. Check for cracked or leaking reeds. Replace as needed. Has tors be deleted??? If not...
  6. Tooloose

    HELP!!

  7. Tooloose

    Complete list for top end mostly Wiseco

    Complete list for top end mostly Wiseco
  8. Tooloose

    I’m still putting time on the china cylinder, piston and ring set! Getting ready to upgrade to...

    I’m still putting time on the china cylinder, piston and ring set! Getting ready to upgrade to Wiseco Prolite piston ,rings,roller bearings
  9. Tooloose

    Awk can you give a part number for the hubs that are 4 on 115 bolt pattern and will fit the...

    Awk can you give a part number for the hubs that are 4 on 115 bolt pattern and will fit the stock blaster spline ?
  10. Tooloose

    Awk 02 what hubs did Yamaha use that matched the 1996 Blaster stock axle spline

    Awk 02 what hubs did Yamaha use that matched the 1996 Blaster stock axle spline
  11. Tooloose

    Axle Length

    I’ve found two rims that are nine inch verses 8 they are 4 on 115 pattern . What hubs do I need to get to replace the stock blaster hubs to hook it up???
  12. Tooloose

    I was told that certain banshee hubs will work but some are 4x115 bolt circle and some are 4x156...

    I was told that certain banshee hubs will work but some are 4x115 bolt circle and some are 4x156 mm bolt circle. Thanks
  13. Tooloose

    Can you tell me what hubs I need to order to use 9 inch diameter rear rims and tires on my 1996...

    Can you tell me what hubs I need to order to use 9 inch diameter rear rims and tires on my 1996 Blaster?
  14. Tooloose

    Especially what year are the 4x155 mm hubs for banshee’s? I’ve been told some years are 4x156...

    Especially what year are the 4x155 mm hubs for banshee’s? I’ve been told some years are 4x156. Thanks Tooloose
  15. Tooloose

    Ask what hubs do I need to buy so I can the 9 inch banshee rims and tires on my blaster?

    Ask what hubs do I need to buy so I can the 9 inch banshee rims and tires on my blaster?
  16. Tooloose

    More info on the Chinese Blaster cylinder

    Yes and polished the transfers top to bottom , replaced the crankseals and new gaskets all the way down to the factory oiler and new Boysen reeds and complete carb overhaul. Premium 93 pump non ethanol feul only and the tores system is still fuctional.2 years later now and it's still running...
  17. Tooloose

    Comment by 'Tooloose' in media 'Alternate view'

    Hey bro! I think your rear tires are backwards! The tractor grips should face forward so they will unload in muddy terrain. Try it and see, just a few minutes work and 8 nuts. Peace ✌️✌
  18. Tooloose

    Hey Awk! I'm getting ready to put a new piston( Wisco pro lite stock) replacement ( stock )66...

    Hey Awk! I'm getting ready to put a new piston( Wisco pro lite stock) replacement ( stock )66 mil. Is the compression ratio higher with this prolite piston? The the current piston is a China replacement Stock piston kit. It has relief on the piston top, facing the exhaust port.
  19. Tooloose

    need jetting advice

    Sounds like a large air leak ! Or a small one, Awk sell him a leak tester!