Search results

Ill do a compression test tomorrow. I already have a new plug in. Standard jet and standard exhaust. None of the pedals / reeds are broken. Air filer is clean and i oiled it again. Ill check the float level again. Ill do all this tomorrow and give you guys feed back.. Thanks guys

Hi There guys. Hope that you are all well! A while ago i posted that i had problems starting my bike and then when that was sorted i had problems with the idling. This Blaster is running but i dont seem to have its full power. I suspect the power band doesnt kick in. Before i stripped the...

ill do a compression test within 2 or 3 days. Ill let you know O'connor. thanks mate. The reeds did some work but they seem fine!

I got it started! I bought a new petcock! That was the problem! But i still dont have the full amount of power that i used to have. Powerband seem missing. Any advice????

Must i disconnect it somewhere on the CDI?

No after market exhaust. Just powder coated the exhaust. On what setting should the needle clip be for standard pipe and reeds. Also how do i exaclty bypass the parking brake wire?

Thanks for your reply Teflon. Air screw is 1 and a hlaf turns out.. i also stripped the wires on the tors, so its eliminated.. so the tors isnt the problem. fixed the slack in the throttle cable. Its all standard as far as i knows. how do i know what jets these are? Ill check the placement of...

Hey Guys I had a post on here that i couldnt get my 2006 blaster started. I actually got it started now after getting rid of the flooding and a new spark plug. I get it to start but as soon as i give throttle it dies. Also too much play on the cable. I have tried the TORS elimination things...

Thanks man.. I fixed up the petcock valve. The carb is clean. The bike starts up but doesnt ref up.. If i give it throttle the refs drop.. like the engine smothers. It could be the tang adjustment

I fixed the petcock valve. it starts up, but it doesnt rev up. I have to give it throttle to keep it running, if i give too much throttle, its like the engine smothers.. like dropping in refs... what could cause this?

Hey Guys I cant get my quad started after i cleaned the carb. It seems to get fuel cause it comes out the overflow. All the vitals are good. I have fuel, tap open, i have spark etc.. I actually dont know what to check anymore! I need a new fuel tap as it doesnt shut off the fuel completely...

Hi Guys! I cleaned up my carb yesterday. Installed it today and it still leaks from the bottom overflow on carb. Infact, now the bike doesnt wana start at all.. Plus the fuel is pissing from the manifold / Exhaust mount? Please help guys. From what i know, if the fuel comes out there it means...

Thanks a lot for your help! Appreciate it! Isnt there a better to route it that it doesnt piss all over the front suspension etc?

Powder coating is the best option. We have a powder coating booth at work so i get my rims and all parts powder coated free of charge and it last much longer than the can spray.

Hey Guys! Hope you all having fun! Im having a problem since i topped up my transmission oil. Close to where you fill or insert your transmission oil, theres a pipe that leads up towards the front of the quad, i would say towards the steering, right in front of your tank.. i took a ride...

Thats awesome!! im sure doing the graphics on those templates is the difficult part! Im In South Africa!

Okay that sounds cool! Where are you from?

Yip. Defnitely a 2007 model. Dont know that happened. It even says that on the paper. Thanks for the help Mark, maybe when you done ill buy a set of stickers from you!

I also did the sandpaper job on mine, just used dish washing soap and 3 stages of sandpaper, good polish afterwards, worked like a bomb! Graphics is the new problem now.. Ebay is crazy with prices

Im also looking for graphics for a white 2007 blaster. Too expensive at Yamaha agents