Search results

Not sure the size. Somewhere around 36mm Barely used if at all.

I have a complete blaster for sale. Parts to note are: full LRD exhaust Engine was 05(already tore apart) +6 swing arm. Ask for anything. Had to post this quick but will post pics and prices soon.

So I have a quick question, if i purchase the stator and flywheel, CDI, coil, regulator/rectifier for a dt200 will I be able to install a regular 12v atv battery? I'm trying to mount some of these on the blaster

32:1 premix Wiseco Piston stock bore 28mm keihin pb carb Lrd exhaust Rechambered head Ported Stock reedcage Open airfilter box These are the current mods I am planning on my current build. Funds are limited so I would like to know, how much more power would I get if I had a vitos+3mm crank...

Does this look like a factory Yamaha cylinder? Or is it a cheap aftermarket?

First question: i have a cr80 that can only be ridden for a couple hrs a day because it will start to bog as if it was flooded. After letting it sit for a day or two it will run good again for a couple hours. I have checked everything. It's all stock with a 122 main and needle clip at the very...

I have a cr85 that's all stock except for a fmf pipe. It won't stop leaking coolant from overflow. I switched the radiator cap off a working cr80 and still leaked. I did a leakdown test to make sure it wasn't a crank seal or head gasket leak and it held pressure. I checked the impeller and it...

Carb and crank are brand new, (never been used) The rest work like new and are in excellent condition.

I have 2 split bottom ends(cases,transmission,gears,clutch,etc.) 2 of everything. Never before used 240 Vito's bbk(head and cylinder) $200 plus shipping (+3 trued Vito's crank(never used) (sold,sold,sold)) LRD right bend pipe full $300 33mm keihin carb(new) $100 Have more, just ask. might...

So what do you guys think? Simple jb weld fix? I think I'm going to try some and hope I don't have to disassemble the top end again. I was leak testing and felt a little air when I spotted this.

I have an engine that I want to install a Vito's 3 mm crank in. I had the head rechambered by Ken O'Connor last year. So my question is will I still need to use the spacer to avoid detonation? Or do I need to send him the head again to rechamber it specifically for the added stroke?

What can I do to check where the leak is if I can't even hold 1 psi. I suspect my issue is in the bottom end because it is new to me.

Just received a kehin 28mm. I purchased some main jets with it also. I installed a 152 main to start with and left everything else stock. My problem is the motor doesn't rev out. When I ride it there is no power like it's running too rich. Mods are pro circuit exhaust, premix 32:1, no airbox...

New motor to me. Rebuilt top end and when I went to put it together I noticed the clutch lever was way to easy to pull. I tried adjusting at the cable and nothing. Then I took the right cover off to take a look and noticed the lever doesn't even move the plates. Tried the adjustment on the...

I am getting what seems like an airleak symptom. At idle, when I press the throttle and release, the rpms don't go down all the way for a few seconds. Also, when the motor warms up, it idles higher until I pull the clutch in, then it goes back down. I have leak tested 2 times already and it...

Just bought another blaster. I can keep it idleing with the adjustment on the handle bar and the adjustment on top of the carb but the idle screw on the side does nothing. It has the tors delete kit. All stock except pro circuit silencer. I leak tested before I ran it . 32:1 gas mix.

Whats the little black L shape fitting on the carb?

Anyone ever take their blasters up to wv? What trails are best for these little monsters?

I was installing the reedcage and intake manifold. I put the cage on along with the 4 bolts. I finger tightened the bolts Went to tighten with ratchet and o e of the bolt broke off flush with the cylinder thread. So now i have half the bolt stuck in the thread and nothing to grab to twist out...

Whats the torque in ftlbs. For the bottom end case bolts?