Search results

Pick this one up for $500. So far I have found it needs a rear tire, front brake pads, fuel line, tank flushed, and a leak at the header fixed. I just unloaded it ten minutes ago, compression is good starts first kick. I haven't leak tested yet but I am figuring the brake lines and the...

I would post a link but they come in, tons of different colors 13.5" and 14" ebay special piggyback style front shocks. Looks to me like the lower eye would break off if you bounced on the front to hard, has anyone been brave enough to try a set. Maybe on a bike that you were about to sell or...

Run across this in excell format it lists initial diameter, diameter just below clip slots, length, Length to taper (s) taper angles. Takes a second to figure out how it's put together but look at double or triple taper needles and it makes it easier to understand. Nearly every needle mikuni...

Anyone ever used these, the tread pattern is like an ITP hole shot, or a Kenda Dominator, and the are available in 20x11-8 for $125 shipped. I can also get what is or looks like Kendall Claw in 20x11-8 for $130 new locally, I think they bought a warehouse full or something and run a small parts...

My plug boot which I think came with the crappy orange Chinese coil, which the previous owner was kind enough to install. Anyhow the spark plug boot took a crap today and dropped the little brass plug latch out of it, the clip that hold tight to the plug flew into oblivion. I made a temporary...

Oh Shirt I just picked an entire raptor 660 setup. spindles, hubs, rotors, calipers, pads, master cylinder w/ rubber hose, looks like everything but the splitter and metal lines. For get this $89.99 shipped :oops::eek::eek::eek::D:cool:. Oòooooh yeah (said macho man randy savage style)...

To support new top end work which is making its way to me from Conecticut, I ended up buying : HD clutch kit (HD springs, and full plate in place of helfplate/wave washer) 2" swingarm extension (bolts onto the stock carrier yoke, carrier bolts to extension in a stock manner. 520/100 link Orin...

The hub, sprocket, and axle come out fine, no problems there thankfully. I stopped last night after getting one bearing and the center sleeve out. The problem is that the carrier itself has taken some abuse at some time and the edge of the lip where the bearing goes in, has some dings and dents...

OK proper jetting takes a few 30+ second long WOT runs to set the main jet. Proper breaking requires no WOT until at least the end of the first tank, no sustained WOT till after the second tank, at least many hours of running before properly setting the main jet. P I realize that...

I was in my garage removing decals and the leftover glue, looked over at my $3 pack of steel wool with coarse, medium and fine grits. I took a moment and cleaned a couple spots and pieces, and began to wonder what the word was on protecting the plastic after polishing it out with the fine grit...

For those of you who aren't content to with a stock needle in your modded blaster and have moved to different ones , How did you go about choosing needles to try? What needle and clip are you currently running? With what mods? What did you do to test various needles ? What was it that caused you...

These carbs are an exact fit to the intake and air filter boots. Have a quick jet change carb bowl on it. Requires a non tors throttle cable. Can use the stock blaster slide. Has the idle screw mounted on the side. Comes with a #35 pilot jet. Can be found on ebay for less than $20 For all the...

Curently I am working on my cylinder , the timing numbers are based of depth of top edge measurements and known deck height (it's easy to see where the ring topped out at and measure from the top of top ring to top of piston. It isn't perfect but it's close and my cuts are made conservative...

OK so I got the bottom end done, and am waiting on the money to send the top end off. I want to go ahead and put the bottom back in the frame and hook up basically everything but the carb, pipe and plug. How much harder is it really to put the top end together, while it's on the machine. I...

Picked up a good working 400ex shock from E-bay for $20 plus shipping. Odered the bushing kit with bolt and nut for $25 shipped from the Ken O'Conor Racing website on a Wednesday afternoon, Friday morning when the mailman ran at my Home in North Georgia he delivered my package from Ken's Shop...

First ten bucks shipped conus takes it. I bought this cap it comes with the thread in cable adjuster and what looks to be a new gasket. I bought this in error not realizing g that the stock carb has a small body but is widened at the top to use the larger cap. The Vm28 I put on uses the small...

Toomey sells a high temp silicone rubber O-ring that goes inside the pipe to seal to the flange. Toomey sells one for $6 or $7. With a minimum of $12 shipping. Sorry but I am not spending almost 20 bucks on a 3 dollar o-ring. It's #223 high temp silicone O-ring Has anyone already take...

There has been more than once that i wished I could have a little extra cooling, at the top of a long and technical (if not particularly steep) hill, or when trail conditions or following a group cause you to spend alot of time under load at that one throttle position you know isn't quite as...

Here is a place to out pics and specs of various needles, for mikuni carbs, particularly the 5 series used on the vm26ss, vm28-606 etc. IIRC #5 series needles fit the vm series from 24mm or 26mm right on up to 32m or34mm, as well as tm series of similar throat size. If no one chimes in with a...

I need to know where to go to get info for my blaster if the info can't be found here on BF. Maybe you could raid the designers, engineers and manufacturers , archives? Seriously, I have found nearly every answer to my blaster questions here, as well as answers and fixes for problems I was...