Search results

  1. A

    jet question

    So I bought n 01 warrior 350. Has stock carb n I bought a dyno jet kit? My question is are the dyno jet numbers the same as the stock jets?
  2. A

    blaster for sale

    I have a 96 blaaster that I am selling. I don't want to get rid of it but I need money. I'm asking $800 see my SIG for all mods and I also did a full rebuild this past winter with all new bearings and bushings though out the engine and chassis. Any questions can be sent via text to 802-451-6948...
  3. A

    axle housing

    Every so often my axle housing loosens up and starts to roll back and forth. I have put on lock washers and it lasted longer but just recently came lose again. Is there anything that I can do to stop this from happening on its own?
  4. A

    94 dr 125

    So I was working on this Dr 125 for a buddy n finally got it running without it falling all over itself. I first took out the fuel adjustment screw and cleaned it up then put it back in and turned it out 3 1/2 turns. Second I took out the jet needle and placed a small nut between the clip and...
  5. A

    carb size and jetting

    I was wondering if anyone could tell me what size carb this is and where I should start off with jetting for my mods?
  6. A

    boysen ports

    OK here it is, I just drilled some boysen ports in a test cylinder and would like some feed back from everyone. Keep in mind I don't have a way to build up the weld on the outside so I don't want to run the risk of blowing thru the outside wall. Any tips will be considered and appreciated...
  7. A

    cylinder

    I am looking for a cheap cylinder with no porting done to it.
  8. A

    jetting kits

    So I have read lots of great stuff on the lrd jet kits but I can't find one that says its for a blaster and the ones for the yzf 450 says with a stock motor n aftermarket pipes. Where can I find n lrd jet kit for my blaster with my mods? Also does anyone have any knowledge about these jet...
  9. A

    porting

    I will port ur engine for 125. That includes cleaning all casing flaws and opening the intake and exhaust ports. I currently only have the race logic templates so if u want something different just contact me and we can plan ahead. Here is a link to my work race logic porting
  10. A

    jet size

    With all my mods in my sig what size jet shouldni start off with for the heat cycles n break in as I just had a bore done courtesy of kor.
  11. A

    question for all the lifers on bf

    Are the case alignment pins really a must have when putting them together? I have new ones for the cylinder but can't find any for the case around here n don't want to order them if I don't really need them. Any input will be most helpful.
  12. A

    question

    So u am finally in the process of putting my engine back together after a complete tear down for a complete rebuild on my bike. My first question is after I do my leak test and heat cycles, do I have to take it easy for the first tank when I did a day port n the bore didn't change n the piston...
  13. A

    steering stabilizer

    I was hoping that someone could post pics of how a steering stabilizer is installed and mounted on a blaster. Thanks ahead of time
  14. A

    lrd pipe

    I may be able to talk my buddy into swapping my FMF for his led but his silencer is really quiet and Idk if I want it quiet, can my power core be rigged to the led? Or should I just stick with the whole setup?
  15. A

    banshee axle

    So I just put together my axle yesterday with a banshee axle, n my housing isn't turning as freely as before and I have the nuts only hand tight? It has brand new freeze n new bearings. Idk if I left something out or if its normal to be a lil stiff at first. Please let me know before I torque it...
  16. A

    DIY racelogic porting

    Here are a few pics of my porting job so far. My exhaust port opened up, (not polished yet) Intake template overlay side by side comparison
  17. A

    carb size

    Here is what I have/will have on my engine, FMF gold fatty, hemi head, aggressive trail port, no lid with a k&n filter. Will my stock carb be fine or should I go up in size?
  18. A

    balancer shaft bearing

    OK here is the deal, I bought a used crank case off eBay n I am trying to replace the left side balancer shaft bearing and I can't get it out. I have put heat to the case around it n grabbed the inner part with players and tryed to lightly tap/pull it out but its not budging. Any tips to help...
  19. A

    lookin for feed back

    Found this on eBay n was wondering if there was any feed back on it http://item.mobileweb.ebay.com/viewitem?itemId=350689815855
  20. A

    flywheel removal

    OK so I have a lil problem, I was working on taking my engine apart today and when I went to pull the flywheel I stripped the threads. How can I get it off and is there any way of fixing the treads?