Search results

  1. giantvt104

    Hows she running iyo...

    This is my 05 Blaster. Readings are 125psi cold and 115psi hot compression, passed leak down 3 times at 8psi for 15mins. Im running 320main, 32.5 pilot at 3/4 open screw, and needle at 3rd clip. vid of idle run with engine warm today at about 70 degrees outside.what do you guys think? mods in...
  2. giantvt104

    Do us all a favor......

    The search function is a very important part of the bf. but when you go to search for something especially issues your having and you find a thread from someone else that had the same problem. then you read up and at the end you find they never updated it explaining what the solution was???? Its...
  3. giantvt104

    Toomey B1 exhaust kit????

    I just got my toomey b1 exhaust kit in the mail today and i was installing it following all the directions and it said to install included 310 main, oil and install uni filter, set air screw 3/4 from closed and set the needle from the 2nd to the 3rd clip down. everything went smooth until i got...
  4. giantvt104

    Boyesen pro series advice??

    So i just got some boyesen pro series dual stage carbon reeds and when i was installing them i found this in the directions: install new reeds using provided rev plate. note: if rev plates are not provided, install reeds using stock reed stop basically the boyesen rev plate is a piece of...
  5. giantvt104

    rtv silicone question???

    so recentley i had to tear down my top end to inspect it and when i put it all back together i got brand new oem cylinder, head and intake/ reed gaskets. when i was putting it all back together i had some rtv form a gasket sitting there so i decided that it might a good idea to apply a thin coat...
  6. giantvt104

    2 stroke oil

    Now that i have my oil injection deleted. i am shopping for pre mix oil. i really like maxima stuff. i think they produce a quality product. so im trying to decide which oil to get and start using consistently. maxima super m pre mix or maxima castor 927. they both seem good to me but im not...
  7. giantvt104

    engine issues part 2

    Hey my original thread was here: http://www.blasterforum.com/general-support-17/no-start-bad-noise-46551/ Thought i could get more in the engine section then in gen support. After yesterday issue. today i pulled my whole top end off to see what was going on. first i removed just the...
  8. giantvt104

    No start...bad noise!!

    today i went to do the oil block off and i removed the pump cover then removed pump and then the clutch cover. i pulled the top c clip and the plastic gear off the pump. reinstalled the pump as the plate. i sealed up the holes in cover plug, the two pump ports and the carb port. put it all back...
  9. giantvt104

    leakdown tester

    I had a vacuum/ pressure test kit already. So all i needed was the fittings for the intake. Thanks to phragle for the diy. I was able to fab up this leak down tester. if i didnt already have the pump/ tester it wouldnt have been very cost effective cause it costed me over 100 bucks but since i...
  10. giantvt104

    Crank seals leakdown testing?

    So ive been noticing lately a burned plastic smell after running a little and when i pull the plug it really smells strong. since i got it imo it seems like an excessive amount of white smoke coming out the exhaust. So taking this all into account i read up on it and was leaning towards leaking...
  11. giantvt104

    Factory service manual vs. clymer?

    I downloaded the factory manual, 03-06 supplement and parts list. Then i printed the whole 400 pages and put them in 3 ring binders. It is awesome to have and has been so helpful. My question is about the clymer manual. Does it have anything that i would need beyond the factory one. Are their...
  12. giantvt104

    Jetting and plug chop guide

    I just found this online and it seems pretty informative so i figured id post it: Spanky's Jetting Guide: A correctly jetted carb makes a tremendous difference in the torque, midrange pull, top-end pull, and over-rev of your engine. If you have never jetted your bike correctly, you will...
  13. giantvt104

    400ex shock complete!!

    I picked up a 400ex rear, Kens bushings and bolt kit, and a couple washers. i used a 15/32 drill bit vs 12mm cause it was closer to my actual dimension. maybe that lower pin is worn a little. had to remove airbox cover for now until i figure out what mod i want to do with that. Took a little...
  14. giantvt104

    Outerwears

    I had to remove my airbox cover for fitment of the 400ex shock. so i was looking into outwears air box covers. the velcro ones. i have a 2005 blaster with a stock airbox and stock style pro-filter. when i research them i find that they only seem to go up to 2002? i know alot changed between 02...
  15. giantvt104

    Warrior rear hubs

    I just grabbed some warrior rear hubs off ebay and i know that both banshee and warriors fit on my stock axle but my question is are shee and warrior hubs exactly the same or is there any diffence like width etc? heres the ones i got 10 + 15 shipped eBay - New & used electronics, cars...
  16. giantvt104

    400ex shock help

    Ok so i got a 400ex rear shock and i was going through it cleaning everything up and i see a few screws. From what i read this shock has 3 adjustments: Preload, compression, and rebound. The 2 big rings on top of spring are for spring pre load. From what i read the with the ressie facing me on...
  17. giantvt104

    lrd exhaust mounting??

    Lrd rfx pipe and silencer. What do they use to mount to the engine exhaust port?
  18. giantvt104

    exhaust packing

    I searched around on here and found a good amount of threads on exhaust packing. My question though i couldnt figure out. basically is the stock blaster silencer supposed to have packing in it. cause when i removed my end cap there was nothing inside :-/ ? also if its supposed to what is the...
  19. giantvt104

    Whats goin on everybody?

    I just joined the beginning of the year. I had picked up a really clean and well taken care 05 blaster. Havent been into it for a while!! Always had a thing for 2 strokes though. Basically for the last month i been on here alot and been doing tons of reading. Everytime i think about...
  20. giantvt104

    2005 blaster vertical rear play

    Hey everybody. Im a new member. I just picked up a 2005 blaster 99.9% stock. Previous owner had to have taken really good care of it cause it really is in great condition. the only thing i notice is when hold the grab handle and lift up and down i can feel play vertically between the top and...