Search results

ok so i will pull the exhaust tomorrow and check where i can see the rings but i checked out my reeds and they looked good and i looked into the jug and pushed the kick start easily with my hand and it looked ok however... when i was putting my reeds back in i decided to clean them off where i...

ok so we went riding on buffalo mountain and i started having problems with my throttle getting tight then i would lose all pressure on the throttle. i got aggrevated and started tinkering around with it. turns out the tors unit isnt good with mud holes so i tried my best to avoid them as i came...

i thought this site was to share with people. my folks taught me to share. nah im just messin with ya. i cant wait to see where this thread is goin. deffinately be following this one

dont let people make it seem too complicated when its extremely simple. the air box is plastic so dont buy strippers they are rough on plastic pieces. good rule of thumb is to always clean a prepped are with rubbing alchohol because its totally safe on all paintable areas. get some sandpaper...

hopefully he still gets on here so he can see what all hes missing out on. might make him sick to know that i put my blaster against my cousins 05 kfx 700 in a little over an eighth mile drag and beat him by about 15 yards. he gave 5700 for his kawi and i gave 600 for my blaster all though its...

i think something is screwy with my computer slick cause it takes me all over hell and half of georgia when i do a search but never where i wanna be. thank you for the link greatly appreciated

so i did a search including the title and didnt find anything, ive read a few other posts and i get conflicting comments about the 03 tors unit. basically what do i have to do to remove it, just buy a kit or can i unplug it until i get the kit someone posted on a different thread that unplugging...

anytime , im full of small pointless may look good or may not ideas haha

haha thanks, yea if i knew how to go about doin that i prolly would haha id like to have my name on something other than a bill. it works really good and i personally think it looks good too but im into oddball stuff like rat rods and such

looks great man, its like the others said, ur not using it as a wheelie bar so i think it looks good. i make mine out of 1 inch flat bar on the sides and two pieces of 3/4 inch square tubing in the middle cause ill deffinately be scraping the asphalt with it haha but i work at a fab shop so i...

ok so back on topic with the exhaust stud. i couldnt find a stud however i found a 13mm bolt thats 1 1/2 inches long with a 8 x 1.25 thread pitch and it turns out that the bolt itself is too long haha so i took the stock nut and threaded it up the bolt upside down so that the washer part of the...

haha i seen a thread on here where someone shows how to do it without buying a block off by using some black silicone and cuttin the hoses. dont seem hard, i think thats what im gonna do.

yea its a great place it just gets old when thats the only place you go haha its a lot of fun when you go with a group of people. i went last week and sunk my blasty in a pond on top of a hill, had to drag thething out cause i wasnt walking all the way down the ridge to find help. let it sit and...

well im still runnin the injection tho im considering removing it before trouble rises

the tubing u used mustve been thinner than what we used. i hope this didn set ya back too bad i was just tellin ya what we did. im sorry it didnt work for you as well as it did for us:(

me and my coisin used two pieces of pipe that were about half inch bigger than the pipe he used for his and slid them onto the pipe on both sides of the line that he wanted it bent on and slowly bent it but as we were bending we slid the two bigger pipes apart slowly then cut a small piece off...

so is there a good place to order yamalube or amsoil. the local yamaha dealer is out of the question cause the guys a f****ng crook. he waanted 14 bucks for a stock ngk plug for my blaster and 55 for a oem replacement airfilter. and i didnt think about the varying tremps in my blasty affecting...

Yea haha but I haven't had any problems out of the poulan pro oil, it did smoke like a diesel truck when I romped on it haha.

well i ran into that problem and luckily i noticed it before i welded. i actually just unbolted everything to where itd be loose on the blaster so i could turn it a little and get a better weld, im sorry for the confusion. and im cheap lol buying a stud is gonna be a last resort, i work inside...

ok so if theres a thread on this ive missed it cause ive already ran a search, maybe i just went thru them too fast if so im sorry. ok so i had taken my exhaust off and welded it to be a one piece exhaust. i thought it was a good idea. when i was putting it back on my blaster i didnt listen to...