Search results

  1. 91yamahablaster

    fuel issue

    well tryed to start quad today and it wouldnt start so i started playing around with a couple things and found that it has spark and compression. so i started looking at fuel well i just got the hunch to poor some fuel directly onto the filter and it started for a breif second then died well i...
  2. 91yamahablaster

    im screwed

    welll finally got some me time so i was going to put the blaster together i was putting on the flywheel and was torqing it to 53 ft pounds got it to about 40 and it striped! the threads look flatend but i dont see any breaks in the thread. what do i do now?? please help. if any one could tell me...
  3. 91yamahablaster

    crank collar leak!!

    i cant seem to get my collar and my crank to seal i tryed the copper rtv method i applied it to chafer only and put it on to where it would be facing bearing i waited 24 hours like it said for it to set and when i leak tested LOTS OF BUBBlES:o getting frustrated with this pesky thing please...
  4. 91yamahablaster

    need help with crank seals

    cant get the pesky clutch side crank seal out i cant get the thing out i tryed the drywall screw and ive tryd hooks i dont know what else to do:-/ help please im out of ideas
  5. 91yamahablaster

    is it blown???

    i pulled cylinder today and these are the pics
  6. 91yamahablaster

    high rev?

    well got me a new blaster last nigh for cheap but it has a problem i cant seem to fix. i start the quad and it wont idle then i tap the gas couple times and all the sudden it will start reving really high without me doing anything i have to shut it off because it never idles back down. i have...
  7. 91yamahablaster

    What do I do

    Well I figured out why my flywheel key didntn fit my slot for my key on my crank is bent in very slightly so my question is what can I do? If I get a slightly smaller key and put it in there would that be ok? Please any help greatly appreciated getting frustrated with this damn thing
  8. 91yamahablaster

    Woodruff key

    Hey I need help with woodruff key I have bought 2 different keys one off bike bandit amd one from my local bike shop and neither fitX( idk what to do any help at all would be greatly appreciated
  9. 91yamahablaster

    please help me

    well got my flywheel key from bike bandit and went to go put it in to discover its not the right one. i have a aftermarket crank not stock:o so what do i do o the crank is wiesco its not stroker or anything anyone know where i can get the right key and any tips on installing?
  10. 91yamahablaster

    blaster go BANG!!!!!!!!

    well went to try the third attempt at starting my blaster for the first time ever and i was kicking it and it made the loudest backfire i have ever heard and shot a flame rocket a good 3 feet out of the exhaust?:o i know its not suppose to do that lol well my question is timing does a 2 stroke...
  11. 91yamahablaster

    help!!

    well i got power to my coil its getting around 7 volts but i got nothing going to my spark plug boot? i did the ohm check and the coil is in spec any ideas as to what my problem is
  12. 91yamahablaster

    help please? many questions

    ok so first off i think i attached the photo no sure if it worked what is the gold bolt spot for and what is the size. ( the gold bolt i put in so you can see where it is) now second problem my blaster has no spark:o i have checked wires and its not a bad ground or anything like that anyhelp is...
  13. 91yamahablaster

    spark plug

    hey guys first off thanks in advance you guys are always very helpfull ok so now to my problem just got done doing full build of my blasty. bought it off guy for $100 it needed full engine rebuild and some other misc parts. now that i have it baack together i want to see if it will fire up only...
  14. 91yamahablaster

    cylinder sleeve?

    got a cylinder from a guy who told me it had never been bored so i went ahead and ordered a .020 piston for it because he said it would need it. got piston today and took it to local bike shop only to find out the cylinder is at 68.20 something so now i got a piston thats to small a cylinder...
  15. 91yamahablaster

    cylinder honing

    is it possable to hone a cylinder to fit a 66.42 piston i didnt think it was but my moms friend is trying to tell me otherwise? any help would be appreciatedI:I