Start Up Problem

Getoffdrive49 · Jun 16, 2015

Please Help, i've changed the oil, cleaned the carb properly, clean air filter & it still wont start. Everytime i kick the kickstart or push start it the oil light blinks. I don't know whats the problem.
Also i used 5w 30 oil is that a problem? Could wrong oil be a problem?

Please Help

Blasturd · Jun 16, 2015

have you checked for spark?

Herpderplol · Jun 16, 2015

Where did you put this "oil change" ?

the oil light is a warning for the 2-stroke oil. has nothing to do with oil in the transmission

Getoffdrive49 · Jun 17, 2015

Blasturd said:
have you checked for spark?

I've just brought a new spark & installed it

Getoffdrive49 · Jun 17, 2015

Herpderplol said:
Where did you put this "oil change" ?

the oil light is a warning for the 2-stroke oil. has nothing to do with oil in the transmission

I've drained the old engine oil & replaced it at the right place. Its not the first time i done it on a bike but this the first time on the blaster

Blasturd · Jun 17, 2015

Getoffdrive49 said:
I've just brought a new spark & installed it

Installing a new plug does not mean it has spark. You need to check for spark.

Getoffdrive49 said:
I've drained the old engine oil & replaced it at the right place. Its not the first time i done it on a bike but this the first time on the blaster

There is no engine oil to drain and replace there is only trans oil!

bummer981 · Jun 17, 2015

The red warning light is for the injection oil tank in the rear under the seat. If your Blaster is still oil injected you may be low on oil or even worse out of it.

Getoffdrive49 · Jun 17, 2015

Blasturd said:
Installing a new plug does not mean it has spark. You need to check for spark.

My fault it has spark

There is no engine oil to drain and replace there is only trans oil!

So what trans oil to use?

MURPH · Jun 17, 2015

https://www.rockymountainatvmc.com/p/935/31839/Yamalube-Trans-Oil-Plus?term=yamaha transmission oil

Bluesman · Jun 17, 2015

Step 1 check oil level in reservoir under seat. Empty

Step 2 check compression. None

Step 3 complete motor rebuild.

Getoffdrive49 · Jun 17, 2015

Bluesman said:
Step 1 check oil level in reservoir under seat. Empty

Step 2 check compression. None

Step 3 complete motor rebuild.

How can i check for compression

MURPH · Jun 17, 2015

speedyslyder · Jun 17, 2015

the red oil light comes on everytime at first start for a few seconds.
even when it is full.... get over it lol
if it is not full enough it will stay on the whole time.

what year is your blaster?
what is 2 stroke oil called/name that you are using?
ngk b8es spark plug
compression test
free flowing gas from tank to carb.
answer all of those or i will keep asking

Getoffdrive49 · Jun 21, 2015

speedyslyder said:
the red oil light comes on everytime at first start for a few seconds.
even when it is full.... get over it lol
if it is not full enough it will stay on the whole time.

what year is your blaster?
what is 2 stroke oil called/name that you are using?
ngk b8es spark plug
compression test
free flowing gas from tank to carb.
answer all of those or i will keep asking

01 Blaster
Valvoline 2 Stroke Oil
Yes i ordered the right one
I have to check for the last two

Pj Uptmor · Jun 21, 2015

You may want to get a service manual for the blaster.

Getoffdrive49 · Jun 21, 2015

Pj Uptmor said:
You may want to get a service manual for the blaster.

I have the manual but i seem to not find the problem

Search

Search

Start Up Problem

Getoffdrive49

Member

Blasturd

Member

Herpderplol

BRRAAAAAAAAAPP

Getoffdrive49

Member

Getoffdrive49

Member

Blasturd

Member

bummer981

Powered by Smoke & Mirrors

Getoffdrive49

Member

MURPH

Member

Bluesman

Member

Getoffdrive49

Member

MURPH

Member

speedyslyder

2 STROKES RULE

Getoffdrive49

Member

Pj Uptmor

Member

Getoffdrive49

Member

Similar threads