Recent content by piezzi

  1. piezzi

    finished my blaster build

    looks sick man...nice job! is that a custom rear swingarm guard? If not, where'd you get it?
  2. piezzi

    clutch arm adjustment picture request

    The post below shows the correct direction of the arm.....facing toward the motor https://www.blasterforum.com/threads/quick-clutch-cable-installation-question.44034/ The little arrow on mine aligns with the inside edge of my case saver and points directly toward the rear of the quad.
  3. piezzi

    Blaster Bogs Beyond Idle

    Yes, that's the one....PN 22-990H. Bought mine from RM using ebay so I got the free shipping.
  4. piezzi

    Blaster Bogs Beyond Idle

    While it's running and warmed up, what happens when you turn on the choke? If nothing, what happens with the airbox lid back on? Airbox lid & choke?
  5. piezzi

    Blaster Bogs Beyond Idle

    Definitely go direct from tank to carb. Have you removed the OEM oiling system and are now pre-mixing your fuel? 32:1?
  6. piezzi

    Blaster Bogs Beyond Idle

    Ok, not a stock carb. If it's also not a 26mm (like a stock carb) then disregard my jetting comment and you're on your own lol. Have you tried it without that fuel filter? Could be restricting your flow. After looking at your video, appears to be an air/fuel mixture to me.
  7. piezzi

    Blaster Bogs Beyond Idle

    Are you back to using a stock carb? Couldn't tell from your write up. Also, is the airbox cover still on? If so, take it off and give it a go. For a stock carb and your pipe, a 270 main jet is a little on the small side.....especially if the air is real cold where you're at. Once you get it...
  8. piezzi

    Extended Tie rod

    LOL you could find a better option than sandpaper. What other options does the OP have?
  9. piezzi

    Extended Tie rod

    Could the broken one be repaired by welding a new threaded end onto it (using a bolt or stud)? That would be the route I'd be looking to take if sourcing a replacement fails.
  10. piezzi

    1999 upgrade

    Looks like it's ready for the track...nice job man!
  11. piezzi

    Stator conversion to battery charge

    The engine ignition switch is its own simple open/closed circuit that doesn't include lighting. A stock blaster's lighting is controlled by the switch on the bars and works independently of the ignition circuit.
  12. piezzi

    Stator conversion to battery charge

    Since they'll be used intermittently, you can probably make it work if you get rid of the OEM light and go with something LED that draws way less. My year 2000 has just the OEM illuminated tail light and not sure if the 3rd gen blasters had brake switches or not. Maybe someone else knows on...
  13. piezzi

    Stator conversion to battery charge

    Asking the real questions now lol. Surprising there hasn't been a blaster specific write up for this mod by now and hopefully others can benefit from our learning. If you're working with stock blaster wiring yourself, kindly let me know if any of the following isn't correct as I'm going off of...
  14. piezzi

    Stator conversion to battery charge

    That should work. 2 yellows wired directly to each side of the lighting coil on your stator and then red and black directly wired to the battery.
  15. piezzi

    Stator conversion to battery charge

    I used a TrailTech battery and voltage R/R. I believe others have used YFZ R/R units. Not sure if the one you bought will work as I can't see the wires. Needs to be a 4 wire DC unit. Here's the specific battery I bought and you can use an AGM battery or any sealed 12v that will fit under the...