Recent content by chee_dee

  1. chee_dee

    Looking for Dimensions for a Torroidal head job please!!!

    I have been doing loads of research on here as well as YouTube. I want to modify my head as per Torroidal for the low down torque as well as the rpm limiter(which I still don't understand how it can limit it but still researching still). The only post I found for the dimensions are for the HEMI...
  2. chee_dee

    How to Remove spring / coil from the shock.

    And the finished product.... BEFORE AFTER
  3. chee_dee

    How to Remove spring / coil from the shock.

    Busy refurbing one of my Blasters and trying to remove the spring/coil for around 5 days now with out spending money on it. Finally used my straps for securing my Quad on a trailer and... VOILA!!! LOL Sharing is caring and a picture tells a 1000 words. Now I can paint this mofo in peace with...
  4. chee_dee

    When is it time to change rings, preventatively?

    That is crazy. Seeing that I never race my quads LOL.
  5. chee_dee

    When is it time to change rings, preventatively?

    I know one should do a Compression Test and once it gets below around 100PSi, start planning to replace the rings. The compression Tester I have is not the proper one for the Bikes. It has the none return valve at the gauge side and not on the plug fitting thread side which means the readings...
  6. chee_dee

    Needle secure plate position please?

    Thanks for confirming. WHat I was thinking too. Hence I never did what the guy in the YouTube vid said to do. Didn't make sense.
  7. chee_dee

    New Blaster vibrating under high revs

    That is exactly what I am doing. I have 3 blasters. 2 have been fixed up and busy with the 3rd.
  8. chee_dee

    Changing needle clip position: Spring HOLDER DIY -LOL

    Yes @EvsBlaster. I can do it without this trick but it's always a mission. The cable ties makes it so much simpler and effective. Adding that extra hand you need to keep the spring.
  9. chee_dee

    New Blaster vibrating under high revs

    Nope, I do all work on my bikes myself. This one, however, I bought and the previous owner did the work. Good question though. Think I will touch base with him and ask who did the honing/boring of the cylinder. Out of the six, one is missing, front right. Bike has no mods, except for the...
  10. chee_dee

    Needle secure plate position please?

    So I have watched a YouTube vid a while back where the guy mentioned how to install this plate that secures the needle. It didn't make sense to me and I have done it in the opposite way he suggested. I need clarity please. YELLOW arrow indicating the plate. BLUE arrow indicating the hole. The...
  11. chee_dee

    Changing needle clip position: Spring HOLDER DIY -LOL

    So, with me tuning my Blasters a lol lately, thought I'd share my easy way of managing this spring for which one never have enough hands to manage. This is probly not something new but I am sure it will help a few. Picture says a thousand words, here goes 2000.
  12. chee_dee

    New Blaster vibrating under high revs

    Nope. It's really small. More like a resonance when revving high. I am really not the expert but I don't know why the screaming on top revs and slight vibration gives me a feeling the engine is running lean. with the 67mm Piston added and no other mods, I have upped the Main Jet from 230 to...
  13. chee_dee

    Weird question but how long will a Blaster's engine brake?

    Thanks @Larry's Shee and @Blaaster .
  14. chee_dee

    New Blaster vibrating under high revs

    So I am finishing my 3rd Blaster and this one feels really strong with nice clean revving except for the Vibration when revving past around 1/2 throttle. Stock Exhaust 230 main jet. Previous owner installed 67mm Piston when the motor seized a year ago. This Blaster really feels strong in the...
  15. chee_dee

    Chain hazzards and purpose of chain rollers?

    Thanks @Larry's Shee .