blastngo92
Last Seen:
Feb 25, 2015
Joined:
Jul 7, 2010
Messages:
591
Likes Received:
3
Trophy Points:
18
Media:
55
Location:
Louisiana
Occupation:
burinin gas

Share This Page

blastngo92

New Member, from Louisiana

blastngo92 was last seen:
Feb 25, 2015
    1. blasterboricua
      blasterboricua
      hey what size tube did u use for the front end pcs on engine side on the extended swing arm
    2. 1bad442
      1bad442
      vote for blaster of the month in contest section theres some nice quads to pick from
    3. scotj77
      scotj77
      so did you go back to the origional guy or find someone who knew what they were doing? send pm's easier to keep track of for me.
    4. scotj77
      scotj77
      I am not using that jug it is screwed now. when drilling one of those ports i went through the to the outside of the jug. Ken oconnor has my new agressive trail ported topend for my 3mil stroker in the mail right now. that jug will make a nice paper weight now. lol
    5. blasterdad
      blasterdad
      Wow, thats a real bummer! Was it a new wrist pin or the old one?
    6. blasterdad
      blasterdad
      What happened? Did you get a defective piston?
    7. blasterdad
      blasterdad
      Sounds like you're getting close, just remember to break it in right!
    8. blasterdad
      blasterdad
      Sorry you got jerked around, that's BS, at least you know it's going to get done now.
    9. blasterdad
      blasterdad
      You have to remove the side cover on the caliper & take the end of the cable out of it's holder, then remove the cable from the foot brake lever by removing the cotter pin, pull the pin out of the brake pedal & cable. The cable itself should now just slide out of it's mount on the frame. (toward you)
    10. blastngo92
      blastngo92
      looks like im not taking the blaster to little river .. stupid lawn services
    11. blastngo92
      blastngo92
      lol no still waiting on them
    12. blasterdad
      blasterdad
      When I accepted your request it pretty much asked me yes or no, can't really explain it in exact detail, I've only done it once, your my first friend :^) Did you get your cylinder back yet?
    13. blastngo92
      blastngo92
      Heard from the guy down at acadian lawn service the bore fore the cylinder is almost done
    14. blastngo92
      blastngo92
      Ready 4 the first week of agust me and powerhouse74 r gona hit it up at little river
    15. blasterdad
      blasterdad
      I hear Krylon Fusion is da bomb if ya prep it right!
    16. blasterdad
      blasterdad
      Sorry bout the 3 day late reply, been super busy at work, hav'nt had time to even turn on the 'puter. It should'nt take a week to bore a cylinder, (unless they're as busy as I am) Who did you take it to?
    17. blastngo92
      blastngo92
      Ugh i hate rick astley
    18. blasterdad
      blasterdad
      I'm not sure, I think the year change was 03-06 but I've seen people on here do it, so I'm pretty sure it's not that hard, ask freek, he'd know for sure! lol.
    19. blastngo92
      blastngo92
      Really bored so i took some pics of the banshee
    20. blastngo92
      blastngo92
      Got new parts posted it in my album
  • Loading...
  • Loading...
  • About

    Location:
    Louisiana
    Occupation:
    burinin gas
    i like beef jerkey and two strokes...

    riding, hunting, fishing
  • Loading...