Search results

  1. J

    back firing still

    it worked!!! ToRS bite hard. Now trying to come up with other things to do with the blaster. Thx everyone
  2. J

    blasty running mint-thanks for your help

    thanks to everyone for their help in getting my blaster running again. I was bummed to the max trying to get this thing running.It took me six months to figure it out. TORS suck... Thanks for your help again ride on james
  3. J

    i know it aint A TWO STROKE BUT...

    PLEASE HELP AND SORRY IT AINT A TWO STROKE, BUT NONE THE LESS STILL A WHEELER! WHAT IS THE SPECIFIC REASON WHY A FOUR STROKE 1984 HONDA ATC 200 S would bog down when throtlle is applied. Idle and start up are fine. The carb has been taken off three times and cleaned with compressed air and...
  4. J

    back firing still

    i am gonna order that kit and pull it out. I found the dyi on the forum i wil let you guys know how it goes thx for your help again james
  5. J

    back firing still

    no i put the plate in where the injection pump went. I got the billet aluminum plate from ebay, sealed it with high temp rtv and put the bolts back in. I then sealed off the carb inlet with the exisiting tube cut short and plugged that with a tight fitting roofing nail. i then disconnected the...
  6. J

    back firing still

    no i put the plate in where the injection pump went. I got the billet aluminum plate from ebay, sealed it with high temp rtv and put the bolts back in. I then sealed off the carb inlet with the exisiting tube cut short and plugged that with a tight fitting roofing nail. i then disconnected the...
  7. J

    back firing still

    interesting that you need to adjust the air fuel and idle screw. I think the idle screw on the tors is way out out of adjustment. Can you just rip it out? that is probly y the idle was out of control.
  8. J

    back firing still

    now with the flat head screw on the tors... should the screw be in or out? i know the air fuel screw goes in then 1.5 out. What is the tors setting of hand? Is the tors maybe causing the timeing/back firing issues, now completely out of control reving? i need my blasty back running i kn ow...
  9. J

    back firing still

    good morning any more advice for this blaster. I last posted that the blaster was completely gone through like everyone said. even bought the puller for the flywheel. i cleaned all the terminals and such. it seemed to run better then i adjusted the carb air screw then the big screw below the...
  10. J

    back firing still

    this sucks checked the key it looked good. Took the flywheel off with the tool. changed the coil with the spark plug wire attached and tryed that. cleaned all the teminals were the ground is, checked all the wires and cleaned them. plugged the old oil injection on the carb real good so no...
  11. J

    back firing still

    this sucks checked the key it looked good. Took the flywheel off with the tool. changed the coil with the spark plug wire attached and tryed that. cleaned all the teminals were the ground is, checked all the wires and cleaned them. plugged the old oil injection on the carb real good so no...
  12. J

    back firing still

    i will pick one up and let you know how it looks. hopefully the blasty will be running good again. thx again j
  13. J

    back firing still

    to remove the rotor do i need to buy those tools from yamaha. for example the rotor holding tool and the rotor puller? what does the key do anyway... does it hold the cdi in place? i appreciate all the help because i certainly can not bring it to a dealer with the economy lately. j
  14. J

    back firing still

    aka faulty cdi, plug, coil or plug wire huh?
  15. J

    back firing still

    i got the manual from this site and downloaded it . I will check the resistence and stuff tomorrow on the cdi when it is bit warmer right it is 10 degrees. would the cdi cause it to back fire and run like sh*t? what about the exhaust being plugged up? thx man again
  16. J

    back firing still

    hi there everybody, still back firing like crazy and throttle responce is very sensitive. And the blaster will not stay idling. I have cleaned extensivly the carb with new rebuild kit. Adjusted the float to the specs, cleaned out with with compressed air. i have checked the reeds...
  17. J

    back firing and hard start

    awesome info but how do you go about checking the flywheel key? an another question on the carb... on the opposite side of the starter plunger (right side sitting on machine) there is a big hole with what looks like threads in it. Is there supposed to be a screw or needle of some sort in...
  18. J

    back firing and hard start

    the blaster ran over the summer then the kid let it sit for like five months. i changed the fuel and such. Can the reeds just go bad and can you give me more info on the flywheel key? i appreciate it james
  19. J

    back firing and hard start

    hi there 1993 blaster is now back firing like crazy. And it is hard starting. i took the carb off and cleaned and replaced most of the parts that came in the rebuild kit off ebay. 1 Why is it back firing and blowing stuff out the tail pipe? 2 Why wont it stay running on idle? i...
  20. J

    kick start repair

    yes i will take some pics of the blaster and post them. It aint much but at least she is mine again. the guy i sold it to (i was desperate for money i.e.mortgage payment) over the summer left it out in the weather in claremont nh for six months. What an idiot. I asked how much does he want to...