My 1st Blaster
- Thread starter Markblaster
- Start date
Yeah sucks a bit looks like I be getting new bars. Renthal is looking like the best option.
http://www.blasterforum.com/threads/stock-handle-bars.64897/
http://www.blasterforum.com/threads/stock-handle-bars.64897/
More done on the bike tonight. Also got my new handle bars and a free gift.
Old vs New.
My free gift I got from Yamaha shop.
Test fitting the front end.
Run into one problem. Spacer is not fitting as its about 0.5mm to long.
New handle bars on. A lot better and a lot more room. Model is Renthal 781-01-SI-03-219
Only one small thin left is the mirror mount. Going to give it a shave and then I would be able to move the lever up to 5mm closer to the throttle housing.
That's it for tonight. Tomorrow I will put the steering tie rods on and brake line clamps so I can work out the brake lines.
Old vs New.
My free gift I got from Yamaha shop.
Test fitting the front end.
Run into one problem. Spacer is not fitting as its about 0.5mm to long.
New handle bars on. A lot better and a lot more room. Model is Renthal 781-01-SI-03-219
Only one small thin left is the mirror mount. Going to give it a shave and then I would be able to move the lever up to 5mm closer to the throttle housing.
That's it for tonight. Tomorrow I will put the steering tie rods on and brake line clamps so I can work out the brake lines.
I'm betting the spacer is the right length but it's the a-arm mounts on the frame that are 'squished' together from being tightened too much.
Yeah they are a snag fit even without the middle spacer. Everything finger tight at moment. Will have a go on the weekend to get spacer installed. Got the front brake line clamps on. Just have to work out best way to route the line now. Off to look for photos of peoples quads.
Ordered some more parts.
Streamline 7 way rebuildable stabilizer
Folding tip gear shift lever
Front wheel bearings / seals kit x2
Lower A arm bushing kit x2
Swing arm bearing / seal kit
Front caliper rebuild kit x2
Rear caliper rebuild kit
Rear master cylinder rebuild kit
Still need to get:
Rear axle bearings / seals
O-rings for steering stem bushes x2
Tether kill switch
Chain and sprockets
Tyre's x4
Bolts, washers, nuts
Will do engine parts later, After I get the frame powdered and as a roller.
Streamline 7 way rebuildable stabilizer
Folding tip gear shift lever
Front wheel bearings / seals kit x2
Lower A arm bushing kit x2
Swing arm bearing / seal kit
Front caliper rebuild kit x2
Rear caliper rebuild kit
Rear master cylinder rebuild kit
Still need to get:
Rear axle bearings / seals
O-rings for steering stem bushes x2
Tether kill switch
Chain and sprockets
Tyre's x4
Bolts, washers, nuts
Will do engine parts later, After I get the frame powdered and as a roller.
Last edited:
1/2 way down the page is links or I can email you files just PM your email.
http://www.blasterforum.com/threads/gusset-placement-with-diagram.39688/page-2
http://www.blasterforum.com/threads/gusset-placement-with-diagram.39688/page-2
Got some more parts today.
Rear sprocket washers. 2 sets
Upper steering stem washers. x5
Also got the rest of the parts to make my leak tester.
Will put the leak tester together tomorrow and test t for leaks before using on engine.
Rear sprocket washers. 2 sets
Upper steering stem washers. x5
Also got the rest of the parts to make my leak tester.
Will put the leak tester together tomorrow and test t for leaks before using on engine.
You may want to try adding this for pumping them up? http://www.ebay.com/itm/SUPERIOR-QU...f3d4566&pid=100005&rk=5&rkt=6&sd=252476697833
Brought a present for myself last weekend.
Also got a package today. Folding tip gear shift lever, Front wheel bearings seals kit x2, Lower A arm bushing kit x2, Swing arm bearing seal kit, Front caliper rebuild kit x2, Rear master cylinder rebuild kit.
Also got a package today. Folding tip gear shift lever, Front wheel bearings seals kit x2, Lower A arm bushing kit x2, Swing arm bearing seal kit, Front caliper rebuild kit x2, Rear master cylinder rebuild kit.
Test out wheel.
Got my DG rear bumper today.
Going to have to modify it a little to fit but hay its not the 1st thing I have had to modify to fit on this blaster.
Waiting on my braided brake lines and Streamline 7 way rebuildable stabilizer and rear caliper rebuild kit to get here.
Got my DG rear bumper today.
Going to have to modify it a little to fit but hay its not the 1st thing I have had to modify to fit on this blaster.
Waiting on my braided brake lines and Streamline 7 way rebuildable stabilizer and rear caliper rebuild kit to get here.
Started on making new extended bracket for the top of the rear bumper tonight. I also emailed DG and asked about the lower mounts on the rear bumper as there is a 15mm gap on each side of the mounting tabs. Bolts they supplied are to short to mount it on the skid plate mounting holes and there is no spacers for it. I'm not to worried as I can make my own spacers but want to see what they say.
Any ways I got my new long travel shocks for the bike tonight. 16 1/4" Mark performance steelo shocks.
Big change from the 14.5" Works shocks.
Any ways back to the build, I have a set of 2008 Yamaha Raptor 700 front shocks that I can test on the front.
Going to get my chain and sprockets and rear axle bearing/seals tomorrow.
Any ways I got my new long travel shocks for the bike tonight. 16 1/4" Mark performance steelo shocks.
Big change from the 14.5" Works shocks.
Any ways back to the build, I have a set of 2008 Yamaha Raptor 700 front shocks that I can test on the front.
Going to get my chain and sprockets and rear axle bearing/seals tomorrow.
Similar threads
